Standard 22 Moderator 1/2 UNF x 20

[Back_Roads]

 I'm starting to think I over think this 3D stuff

[bduares]

My nerdy lithophane experiment:

Are you printing that with an FDM or Resin printer?

[OldCrow]

NOTE;  I'll be updating the moderator designs on thingiverse to support the following thread patterns.
1/2x20, 1/2x28, M10x1. M14x1, M14x1.25, M16x1, M18x1, M19x1.5 and M20x1

These are all printed threads. 

Done

[Robert 5mm]

NOTE;  I'll be updating the moderator designs on thingiverse to support the following thread patterns.
1/2x20, 1/2x28, M10x1. M14x1, M14x1.25, M16x1, M18x1, M19x1.5 and M20x1

These are all printed threads. 

Done

One more thread if you could please - M20x2 for the Standard and Wraith.

Thanks for all your work

[OldCrow]

NOTE;  I'll be updating the moderator designs on thingiverse to support the following thread patterns.
1/2x20, 1/2x28, M10x1. M14x1, M14x1.25, M16x1, M18x1, M19x1.5 and M20x1

These are all printed threads. 

Done

One more thread if you could please - M20x2 for the Standard and Wraith.

Thanks for all your work

What guns use that?

[Robert 5mm]

Buck Rail adapters use M20x2 for different manufacturers - Beeman, Crosman, Benjamin

[OldCrow]

Buck Rail adapters use M20x2 for different manufacturers - Beeman, Crosman, Benjamin

Ok, I'll try to get it up to Thingiverse this week.  I'm running some pretty big OpenScad scripts right now and they're going to take 24 hours or so to finish.  When they are done I'll get that done.

[TorqueMaster]

My nerdy lithophane experiment:

Are you printing that with an FDM or Resin printer?

That was FDM, Ender 3, white PLA.  It prints standing on edge, roughly 3.5mm thick for the darkest parts, and probably 0.4 or 0.5mm for the lightest areas.    The source image file was only 600 x 330 -- it might look less edgy with a higher res image.

[bduares]

Oh, ok. Might give that a try then. I never did a litho because I thought they were for resin printers

[OldCrow]

NOTE;  I'll be updating the moderator designs on thingiverse to support the following thread patterns.
1/2x20, 1/2x28, M10x1. M14x1, M14x1.25, M16x1, M18x1, M19x1.5 and M20x1

These are all printed threads. 

Done

One more thread if you could please - M20x2 for the Standard and Wraith.

Thanks for all your work

You are very welcome, sir.  This task has been completed for all the moderator designs which are large enough in diameter to support an 20mm thread.  Your M20x2s are up there.  Resolution of those stls is about double that of the ones already on the site.  That makes the file size larger.

[Robert 5mm]

OK thanks again, I will be going to Thing next

[naptemp]

NOTE;  I'll be updating the moderator designs on thingiverse to support the following thread patterns.
1/2x20, 1/2x28, M10x1. M14x1, M14x1.25, M16x1, M18x1, M19x1.5 and M20x1

These are all printed threads. 

Done

Now I have to redownload all your moderators
I especially appreciate the 1/2-28 and M10x1, since I have a few airguns using that.

[guitarplaya39]

Mike,
Thank you for all your hard work and dedication! I put the .22 Standard on my Avenge-X for a quick test - comically quiet and sounds so cool.
I found your cutoff velocity table after printing the Standard, so now I'm printing the Phantom. Can't wait to try the other designs as well!

[OldCrow]

Mike,
Thank you for all your hard work and dedication! I put the .22 Standard on my Avenge-X for a quick test - comically quiet and sounds so cool.
I found your cutoff velocity table after printing the Standard, so now I'm printing the Phantom. Can't wait to try the other designs as well!

Thank you for your kind words.  There are about a dozen thread patterns supported in the files up on thingiverse now.

I think you will like that Phantom.

Those numbers are sort of "theoretical".  I've got a barrel on the way which will extend beyond the shroud of my Avenger.  Maybe then I can get some actual test data on those cut off numbers.

[guitarplaya39]

Yeah, I had it cranked up alittle sending 15gr JSBs at ~1015fps so it would clear cutoff velocity. Same hole at 30yds, but have yet to test at further range. I'll be clearing some brush to hopefully stretch the range to 70yds, so that's then the real testing begins. I just couldn't get over how awesome it sounded lol.
I'm currently printing two of each because my buddy just got a Barra 250z (longer bbl, no built-in mod). It'll be fun testing them on two different platforms. I'll report back some data next time we get together.