First Notos major modifications

[kbstingwing]

Hey David, Looks Awesome, that's 192 shots and still plenty more air, I'm sure the smaller bottle works just fine, you did a great job turning the block, I'm sure you will get lots of PM's for turning services, and the picture when clicked on posts normally
Looking good man, have fun with it, yours is #2...

[Firewalker]

Kevin,

I am thrilled that you shared the drop-block, the Notos has replaced 4 of my airguns with the larger air tank. 

[kbstingwing]

Kevin,

I am thrilled that you shared the drop-block, the Notos has replaced 4 of my airguns with the larger air tank. 

That's awesome, Glad you Like it.

[kbstingwing]

as mentioned above, with a 1800psi regulator, I am getting 730fps, it is possible to increase the plenum space in the drop block by drilling the pathway hole bigger or use a dremel and hog out some space, but be very careful not to take out too much and hamper structural integrity, drilling additional short holes will increase space for air, increasing the plenum capacity, this should increase air volume and give you more Fps, I am going to do some experimentation here in this next week, so please be patient, don't go doing anything until I get back with my results
and remember I hold no liability for what you do....

thanks
Kevin

[BurgerTime85]

This looks like an awesome setup and something I want to attempt for my 2nd pcp rifle. I do not currently have the notos or drop block but I plan to purchase them soon and do this modification.

Would one of you that have done it please post pictures of the parts I'll need to tap? I believe I am capable of performing the job I'm just not sure what parts will need tapping and I'd like to get an idea before I have the parts in hand.

Thank you

[kbstingwing]

I did this just now it's just a quick reference picture of the block

[Firewalker]

Turn this end down to clock properly on the gun.

[kbstingwing]

it is possible to drill into the inside of the block to make more air space for the plenum, just make sure not to take out too much for structural integrity, drill additional channels, they don't have to go anywhere, they just need to make more space......  it Should increase the amount of air like a power plenum, this should increase power.

[Firewalker]

it is possible to drill into the inside of the block to make more air space for the plenum, just make sure not to take out too much for structural integrity, drill additional channels, they don't have to go anywhere, they just need to make more space......  it Should increase the amount of air like a power plenum, this should increase power.

Nope, just get a m18*1.5 male to m18*1.5 female adapter.

[kbstingwing]

it is possible to drill into the inside of the block to make more air space for the plenum, just make sure not to take out too much for structural integrity, drill additional channels, they don't have to go anywhere, they just need to make more space......  it Should increase the amount of air like a power plenum, this should increase power.

Nope, just get a m18*1.5 male to m18*1.5 female adapter.

that would work too.

[BurgerTime85]

I did this just now it's just a quick reference picture of the block

Perfect, thank you

[kbstingwing]

Your Welcome, any time....

[stroo]

Nice pioneering Kevin!  This site is amazing!

[kbstingwing]

Nice pioneering Kevin!  This site is amazing!

Thanks, lots of good stuff here on GTA

[Back_Roads]

  This could lead to the extinction of the Prod 

[bear air]

Sweet looking rigs Kevin and David. Looks like a nice little pesting rig with a lot of shots. Or a nice round at the paper as well.

[Rick67]

  This could lead to the extinction of the Prod 

Crosman's sending out their assassins to TX 

[kbstingwing]

  This could lead to the extinction of the Prod 

Crosman's sending out their assassins to TX 

maybe it will get them to upgrade, make something new instead of trying to ride out the old stuff too long, Marauder is due for at least a side lever.....

[bear air]

+1 and make them so they work on the gen 2 as well.

[rkrr20307@comcast.net]

Been thinking about purchasing a NOTOS for awhile now. Just received the buttstock adapter for my PP750 and waiting on the reg gage block. Then I can see what we can get out of this little carbine. Still may need a NOTOS  and convert to bottle as have been done. Have a KRAL NP03 that is currently being converted to a bottle gun.