NEW Crosman 362

[Psipumper]

Looking over my new 362. I like it.
Out of the box ,675 fps @8  using 14.3 CPHP pellets. Kinda peppy for a small compact pumper.
I am going to get the power up some and mount a scope to see if it is accurate enough for another round of mods.

[sunlitsabs]

Hey guys, is there a good setup for peep sights if I put a steel breech on the 362? If I run a williams peep or similar on a steel breech I imagine I will need a taller front sight but havent been able to find a good definite setup.

[Ragboat]

Hey Sunlitsabs
Here is what I have done to the front sight of my C362, You can make it any height that you need. 
You cut off the blade of the front sight, drill and tap for a 6/32 set screw, cut a piece of allen wrench that fits
the 6/32 set to make the front post the height you need. Glue it in the set screw.
Here is the link to the thread showing what I did to my C362

//www.gatewaytoairguns.org/GTA/index.php?topic=196798.0

Hope the link works.  Well the link did not work the title of my thread is{ My c362 Sight Mods } on page 2

[avator]

Here's what I did......

https://www.gatewaytoairguns.org/GTA/index.php?topic=195418.msg156288775#msg156288775

[Van]

  I like to cut those Crosman ramp sights up too.  Cut the top off drill a hole and use a brass pin glued in for higher visibility than iron pins.  Cut the bottom off and glue the top to a TKO for a ramp painted with a florescent paint. 

[sunlitsabs]

Thanks guys, those are great solutions!

[Charly45]

Anybody still shooting thier 362,??
Any mod updates???
Still enjoying mine.

[tennx]

Anybody still shooting thier 362,??
Any mod updates???
Still enjoying mine.

Not lately…arguing with my used Sentry..(sold as new??)…….lol

[Back_Roads]

 I have 2 at the ready for pest, may go see what damage these will do today while doing yard work

[Wayne52]

I robbed the scope off mine but ended up couldn't use it on what I had in mind so now when I get around to it I'll put it back on for a quick sight in in the attic soon.

[Keepingitsimple]

Anybody still shooting thier 362,??
Any mod updates???
Still enjoying mine.

I'm still shooting and enjoying mine. I ordered a .22 Disco SE barrel and a Maximus slip on adapter for a 1/2-20 can yesterday.

[BerkshireHunter]

Well I’ve shot it a bit and I do like the concept. However, it seems to hold air even after only 5 pumps so that’s a problem. I think it might be the rear sights screw impeding the hammer spring maybe but will have to take it apart eventually. Also had a little trouble sighting it in and I think the sights might have been drilled a tad crooked so I’ll be inspecting that closer too.

Did I mention I shot and broke my Chrony on the first test shot?!  Dang! It was the cheap EBay one but it did work pretty good.

[Tucannon]

I finally got a steel breech for my 362 made a little video for my tube channel.

[moose]

Love mine. now I want to do a .177 version

[dhd]

I finally got a steel breech for my 362 made a little video for my tube channel.

I enjoyed your video.
Wish I could of seen it prior to installing the steel breech on my 362.
Instructions I followed, had me remove the trigger safety and stock.
Your version is much simpler and quicker.
Thank you

[tennx]

Be aware …its been reported that the rear breech screw can crush the hammer spring green guide….the screw on my steel breech was barely short enough not too….it would benefit anybody to read all things 362…good luck

[tennx]

I finally got a steel breech for my 362 made a little video for my tube channel.

I enjoyed your video.
Wish I could of seen it prior to installing the steel breech on my 362.
Instructions I followed, had me remove the trigger safety and stock.
Your version is much simpler and quicker.
Thank you

Do to the nature of the soft metal screws ,i try to limit how much i take these guns apart….by removing the stock u have the opportunity to work on the trigger,fix the wobbly hammer pin and check the clearance of rear breech screw….good luck

[Tack Driver 10]

Power to the people.

[tennx]

Power to the people.

Thanks for sharing….Really enjoyed that vid….made me want to buy one….OH…WAIT …I already have 2…a 362 and a 367….thing looks impressive with the 24’ barrel….

[sunlitsabs]

Im wanting to swap out the breech and valve in the 362. Does anyone know a good resource for dissassembly/reassembly? Or are they pretty simple to pull apart without a diagram?