Any one ever heard of the Dynamic PCP air rifle?

[deerflyguy]

Yeah, Wayne, i ordered 3 sets from someplace in the world for $19.05 shipped (they're supposed to be here next Thursday).
I hated to do that, as I must have two dozen sets of rings laying around, and none of them were 10 mm!

[deerflyguy]

I've tried using offset mounts on several of my guns, and they work quite well, but there really isn't much space on the receiver of the Dynamic, and the mag sticking up is an issue. Doesn't make much difference, because I don't have anymore of them to use either. I've also used pic-to-dovetail adapters on several guns, with good success, but the mag doesn't allow for it on the Dynamic. It could be done, but it would be a cobb job, for sure! Besides, I've got 3 guns to dress up! Guess I'll just wait for the rings?

[Bentong]

I want to see it!

[Rat Sniper (AKA: PaulT58)]

I want to see it!

LOL!  Me too!  I want to see a close up of the magazines!  I have a .177 on order, and like the idea it holds 13 rounds, but would still like to order a couple mags as back-up.  Can anyone confirm if they are the same as the those used with any of the current SPA air rifles on the market?  If so, do you have a part number?  I could then just order direct from SPA and have them in a month or two...

[BigMike1]

I thought i was loosing it with the rings ! lol   I machined .020 off a set that i had to mount my scope.. anyway I get up at 530 to play with the dar and low and behold it is empty after leaving it full to 3000 last night..     Try to fill it this AM and it has a awful leak...  Turns out it had a blown Regulator Oring.. Oh and by the way the orings are two small from the factory. Went to my Fuel injection oring set and replaced them.. The air tank where the regulator sets was so roughly machined that an oring will never seal for long. Had to fix that also..   Next experience be careful when removing a double stacked pellet they can get into the bolt/cocking mec and Very hard to get out Arrr  But When it shoots it is quit accurate    

[rsterne]

How can a regulated PCP ping?.... Mike, did you put the depinger in the plenum?....

Bob

[tracker1955]

Big Mike, sorry to hear you had problems with yours so early also, doesn't help boost my confidence in this rifle when I get one back, just sent mine out at UPS store at 10:00 am this morning. Now the wait clock begins, hope I see it before August.   Also glad to hear there really is a regulator in there, was trusting the info from Deerfly. I'm sure more people will chime in as their rifles arrive. My scope for this rifle was made in China, maybe it will close on the 10mm dovetail better than others, never got a chance to try after no air up problem.

[Taso1000]

My two are on their way back to SG.  I refused the packages.

Taso

[oldpro]

I think I’ll chalk the DAR up as you get what you pay fore. Sounds like it’s 3rd world tooling and quality but at that price it still may be a deal if your a tinkerer if not probably look elsewhere.

[Taso1000]

When my guns were enroute the order details at SG said no returns.  Now after the refused delivery's it has a check box for return. 

Does this option show up for anyone else before today or did SG reconsider returns?

Thanks,

Taso

[Taso1000]

I think I’ll chalk the DAR up as you get what you pay fore. Sounds like it’s 3rd world tooling and quality but at that price it still may be a deal if your a tinkerer if not probably look elsewhere.

Yeah, I didn't want to tinker.  I even have a few unfinished projects but I need a break.   

Taso

[Rob M]

I think I’ll chalk the DAR up as you get what you pay fore. Sounds like it’s 3rd world tooling and quality but at that price it still may be a deal if your a tinkerer if not probably look elsewhere.

doesn't that apply to all the popular guns under 500 bux ?? that's where the majority of the market is , so that could be said about 99% of the guns the average Joe owns.

[BigMike1]

Tracker Its all good!  I had to send my Mrod back it shot 7in to the left at 30ft I was like wth and the new one they sent me shot 5in to the right at 30ft  i just took the gun apart and put the barrel in the lathe give it some straitening mrod fixed.  So the DAR  needing some love is no surprise . Ive herd of guys having $hit luck with 2000.00 FX's so if a couple Orings and my brake hone fixed this thing Im ok with it.Oh BTW My regulator is Adjustable.. I would like another Mag  If they are selling them...

[deerflyguy]

Taso?

I just checked the SG return policies and this one point jumped out at me:

"Packages refused by customers will be refunded for merchandise total only, shipping and handling charges for both the delivery and return shipping are non-refundable."

I suppose that means, because you refused two boxes, you will be charged somewhere around $80-$100 +/- s&h for the refusals? Did you see this before you made the decision to refuse the guns? I'm guessing that when they credit your card for the returns, they will take the s&h charges directly out of the total credit amount due you for your guns?

[Taso1000]

Bill,

No, I did not catch that.  So I guess I'll be out $40 or $80.  I'll email and see if I can get that lowered.

Thanks,

Taso

[BigMike1]

Fly that will be a stiff one ot swallow  Even after the frustration of mine not holding air overnight and the fixing this AM I still like a lot about this rifle . It has its quirks But it is a shooter, I went back to 45yds and the groups stayed in a quarter size hole  Im not even bagged in just shooting off my stepladder!  I do think the gun has potential given a chance Just like the little blue compressors! 

[deerflyguy]

Taso:

Shipping is pretty cut and dried, it's the "handling" charges that sometimes get you! That might include initial order picking, as well as restocking fees? Many companies charge those.
In the case of SG, you will be our "litmus" test?
Please let us know how you make out?

[Nomadic Pirate]

My two are on their way back to SG.  I refused the packages.

Taso

Now, that was quite the radical decision there.

[Taso1000]

Taso:

Shipping is pretty cut and dried, it's the "handling" charges that sometimes get you! That might include initial order picking, as well as restocking fees? Many companies charge those.
In the case of SG, you will be our "litmus" test?
Please let us know how you make out?

I wrote them via their contact options that it was shady to enforce terms that were not on their website.  That is deception, fraud or whatever you want to call it. 

I purchased the rifle in good faith and I didn't want to be the one to bug test or deal with a defective rifle or worse case right it off.  Someone else may think that is acceptable and more power to them but not me. 

We may agree or disagree on all sorts of subjects but as consumers we have rights and recourse.

I bought two Xisico Sentry's for $250 each and they functioned great, meaning they held air and fired.  So saying that defects are acceptable in low priced rifles is where I will have to respectfully disagree.

I will report back with their response.

OP, I apologize for going off topic.

Thanks,

Taso

[TheSaint]

Depinger went in the tube, not the plenum. As this is my first regulated gun, and it was mentioned that it's adjustable, how does one go about doing that that? I'd like to dial mine back a bit. Only getting 30 shots from 3k psi to 1k psi. The gun is a .22. total barrel length is 18". Rifled portion is 16 3/4 inches. The barrel is massive. Definitely Not a straw barrel by any means. And the build quality is meh. My lower priced Sentry's are miles better in build quality.