Introduceing the Black Ops Sniper Dual Cal

[Privateer]

You may have the 'can't hit &^^&' issue due to plastic washers.
I'll give you $75.00 bucks for it.
 

[FrozenVapors]

Nope. Two washers on the breech where it pivots. Stock are plastic and those cause most of the issues I'm told.

shoot! Well i better get on that too! :/

Any ideas for sourcing?

[Privateer]

If you can get them from Gene? There's info in threads about getting them from Lowe's and such.
That's the best thing about GTA. The information is here and all you need to do is ask.
Remember! The only stupid question is the one you don't ask!
You sure you don't want $75.00?
 

[FrozenVapors]

If you can get them from Gene? There's info in threads about getting them from Lowe's and such.
That's the best thing about GTA. The information is here and all you need to do is ask.
Remember! The only stupid question is the one you don't ask!
You sure you don't want $75.00?

Sweet! Gonna have to search the forum for that one!!

[Privateer]

Here's a start.
http://www.gatewaytoairguns.org/GTA/index.php?topic=63310.0
Enjoy the off topic stuff!
 

[FrozenVapors]

Here's a start.
http://www.gatewaytoairguns.org/GTA/index.php?topic=63310.0
Enjoy the off topic stuff!
 

so..... took my barrel off... looks a lot like steel black washers... certainly not plastic :/ You're talking at the part the breach pivots right?

[FrozenVapors]

even if they are plastic, i cannot see how those would even come out :/

[Privateer]

so..... took my barrel off... looks a lot like steel black washers... certainly not plastic :/ You're talking at the part the breach pivots right?

I never worked on the NVD. George did Dusky so I'd defer to his advise on those washers.
Now you want to know about this Chinese Gun? I can answer those questions.
 

[FrozenVapors]

I never worked on the NVD. George did Dusky so I'd defer to his advise on those washers.
Now you want to know about this Chinese Gun? I can answer those questions.
 

hehe! Sorry i hijacked the thread a bit! Will PM George

[Qdoggus]

so..... took my barrel off... looks a lot like steel black washers... certainly not plastic :/ You're talking at the part the breach pivots right?

I never worked on the NVD. George did Dusky so I'd defer to his advise on those washers.
Now you want to know about this Chinese Gun? I can answer those questions.
 

Congrats and good luck. You and I both need a chrony. I'll see if I can find a bkx2 .22 barrel. I'm thinking about mounting some suction cups on the bipods for the glass table I shoot off of. Do I need any special tools to pull it apart completely?

Edit...
I found the barrel quickly and it's cheap too, I just cannot seem to locate a breech block.

[Privateer]

Takeing the 'Fat Lady clothes off' is easy. Just take your time and look at it.
I'll get some pics later.
For the swap to dual cal? Buy a used dual cal Beeman. Post in the GTA classified and you should get an offer.
There are TONS of these out there but We just may have raised the price on them!

Tools I used were a phillips screw driver and a hex wrench.

[silent_airman]

I never worked on the NVD. George did Dusky so I'd defer to his advise on those washers.
Now you want to know about this Chinese Gun? I can answer those questions.
 

hehe! Sorry i hijacked the thread a bit! Will PM George

Sent you back a PM

[silent_airman]

Ya. I'm kind of proud of this.
 

Dude, you should be GTA's official narrator! 

[silent_airman]

TactiKody with the Bi-pods and CP 3x9x40 AO scope


The rail mount is a bad point. I have Weaver rings but they don't fit properly and will take some work to get it set properly.
At 20 yards I shot at a Pepsi can. I did not zero but used the mil dots to pull on target as the scope is whacked due to the rail issue.
Over all? I'm saying this is a sweet mod to get the .22 and still have the .177 should you want it.
Recoil is not what one would expect if you have fired a Beeman X2 version before. Very forgiving and the Bi-pods are not bad at all!
Kind of loose so you need to lean forwards then lean back to get rid of the slack in them.
I fired with one hand under the grip to raise it on target and a fairly light pull into my shoulder.
I hit the can every time after the first shot. 1" or so between hits.
Not bad with a crooked scope.

And you saw it here at GTA first!!!
 

She looks pretty mean. Sort of has the anti-tank look with that muzzle brake! Man, when they come out with the gas ram version, I'll be saving my pennies!

[gashinshotan]

Do you have a chrony? Looks like you can blow up a tank with that haha

[Privateer]

Do you have a chrony? Looks like you can blow up a tank with that haha

Traded my F1 and sent it out in the mail just an hour before this one arrived!
 
It looks big and bad but it's still a .22
It's really a fun shooter and sure makes the neighbors look!
 

[FrozenVapors]

I'm excited for updates on this!

[Privateer]

Changed to the rings that came with this Gun. My Weavers would not fit due to the ungodly amount of paint on the rail.
I could strip the paint but I have doubts about it as it is a cast metal piece of work.
Looks like I'll be looking for a new rail and drill it to fit as I really don't like how high the scope sits now.

[FrozenVapors]

Changed to the rings that came with this Gun. My Weavers would not fit due to the ungodly amount of paint on the rail.
I could strip the paint but I have doubts about it as it is a cast metal piece of work.
Looks like I'll be looking for a new rail and drill it to fit as I really don't like how high the scope sits now.

Kinda not worthy. Could get the g36c rails I bought. They're like $25

[Qdoggus]

Changed to the rings that came with this Gun. My Weavers would not fit due to the ungodly amount of paint on the rail.
I could strip the paint but I have doubts about it as it is a cast metal piece of work.
Looks like I'll be looking for a new rail and drill it to fit as I really don't like how high the scope sits now.

What about http://www.airsplat.com/Items/AC-MNT-HGR16S.htm?