Inovairtech - MAC35

[KnifeMaker]

I can't help but think that Bob is right on here. I've tried them with the gas check type area milled off, and with it left on. Seems the bullets that are otherwise identical, are more accurate with the gas check area left intact, rather than a full width base.


Doug, do you remember what it weighs?

Knife

[airgunwarriors]

Where's the beef?
Anyone have word on the Mac35 ? In production yet, or?
John

I recently received an e-mail from Rick Eustler telling me that many improvements have been made on the final production model and that he should have one in his hands ready for review sometime really soon, like the first week of December or something like that...could be sooner.

Thanks,

Al.
(AGW)

[airgunwarriors]

According to an email update that I recently received from INVT, they recently gave a MAC35 away to someone, so I'm guessing that the final production models are ready.

I've been watching a lot of big-bore air-gun videos lately and based on the performance that I've seen from these various makes, types of big-bore air-rifles; the MAC35 as we currently know it (before any of the improvements that have been made) does not seem to be doing to bad of a job...considering the size of the air reservoirs.

Seriously looking forward to viewing Rick's (Airgun Web) review on the final production model MAC35 and hoping he provides us with performance statistics based on various weighted ammo.

Anyone one else have any updates?

Respectfully,

Al.
(AGW)

[Inovairtech]

Hi Guys

Apologies for the silence recently, we have been completely absorbed with bringing the MAC35 to market.
Reading back through this thread, much of it is off topic, but I would like to address any questions you have with regards to Inovairtech and our products. As I don't get on here as much as I should, please email me any questions you may have directly for a rapid response, on paulb@inovairtech.com
The MAC35 is made on CNC machines to reproduce parts identically.  So once set up, it is far more efficient to run many units to ensure the costs and time for each part is justified. We therefore decided to manufacture the 100 MAC35 limited edition (gold inlay) in one campaign. The first units were sent out about 10 days ago and the feedback response from our customers has been very good. Over the next few days customers will start to send feedback product reviews on our Facebook page and on our webpage.
We have and will be sending a few units out for review with the airgun/gun media, I will paste links here, on our webpage *reviews/links" section and on Facebook when they appear, which hopefully will be within the next few weeks.
We have also opened a store in Las Vegas - details are available on Inovairtech.com "about" section.
For those of you attending SHOT SHOW in January you may like to join us at the range and experience shooting the MAC35 for yourself between 20th and 23rd of January in Las Vegas. If so please email me directly on the address above.
It would be great to actually meet you guys and be able to show you first hand the MAC35 capabilities.

Meanwhile have a safe and enjoyable holiday season and all the best for the New Year!!

Best regards

Paul Baxter

[grumpy]

I would love to get my hands on a 58 gr mold !

Yeah the only way to get lighter is to deck the mold. That is what was done to the NOE mold. It was a 85 gr bullet and now a 71 gr.

I know of one guy on the TAG forum that has a 58 gr Lyman. He is the one that decked the NOE mold. I talked to NOE and they will make a new mold just like what I have if I send them a couple of samples. I'm going to because it shoots so good and this is a borrowed mold.

[KnifeMaker]

I would love to get my hands on a 58 gr mold !

Grumpy, I have a 54.6 gr lyman 257420 here that I am not using.
and if you pick up a NOE 80gr FlatPoint, I can get it down to 59.6. but that's about it.

Knife
 

Yeah the only way to get lighter is to deck the mold. That is what was done to the NOE mold. It was a 85 gr bullet and now a 71 gr.

I know of one guy on the TAG forum that has a 58 gr Lyman. He is the one that decked the NOE mold. I talked to NOE and they will make a new mold just like what I have if I send them a couple of samples. I'm going to because it shoots so good and this is a borrowed mold.

[fortyshooter]

My interest will be on the "planned" .410 double barreled shotgun!!!  I hope it's a break barrel side x side with about 16-20 inch barrel.  .
Any pricing on the current production guns? 

If you guys need someone to review a pre-production .410 shotgun...send it to my "Shotgun Saloon" and I'll give it a full review
on my channel....."fortyshooter1" 

[Inovairtech]

Hi

Thought you might be interested in viewing our Veterans Day Shooting Competition held in Las Vegas, which has just been published on our YouTube channel. Congratulations to Don Leckburg, the winner of the first Inovairtech shooting competition at Pro Gun Club Las Vegas yesterday. After qualifying through the group stages Don went heads up in the final with Larry, the scores were tied after 5 shots so it went to a sudden death single shot nearest the bull playoff. Larry shot first and was close to the bullseye. Don stepped up and with the distraction of the target fluttering in the wind and his cell phone going off at the critical moment he nailed clinched it . Don wins a MAC35/scope combination prize, serial number 11, to commemorate the great service and dedication of the Veterans.


In response to one of the above questions, the shotgun should be available at the end of the 2015 or even early 2016, no pricing is available at present.

[fortyshooter]

Hi

Thought you might be interested in viewing our Veterans Day Shooting Competition held in Las Vegas, which has just been published on our YouTube channel. Congratulations to Don Leckburg, the winner of the first Inovairtech shooting competition at Pro Gun Club Las Vegas yesterday. After qualifying through the group stages Don went heads up in the final with Larry, the scores were tied after 5 shots so it went to a sudden death single shot nearest the bull playoff. Larry shot first and was close to the bullseye. Don stepped up and with the distraction of the target fluttering in the wind and his cell phone going off at the critical moment he nailed clinched it . Don wins a MAC35/scope combination prize, serial number 11, to commemorate the great service and dedication of the Veterans.


In response to one of the above questions, the shotgun should be available at the end of the 2015 or even early 2016, no pricing is available at present.

Well maybe a picture of it when you get to a finished product. Can't wait to see how it will look!!

[Inovairtech]

Hi Guys

just launched the MAC25 we will start shipping these in approx. one month

please see website for details:
www.inovairtech.com

[farmerjoe99]

Shot show review:
http://hardairmagazine.com/news/product-news/shooting-inovairtech-big-bore-air-rifles/
Joseph

[dyotat100]

Didn't take me long to figure out that the reviewer doesn't know much.

.257 pellets?

[Monkeydad1969]

Didn't take me long to figure out that the reviewer doesn't know much.

.257 pellets?

lol---.257 pellets.

[Tofazfou]

Yeah, there are a few folks on ANOTHER forum that call BULLETS pellets.

Its either SLUGS or BULLETS.  There are no 257 pellets........lol

[dyotat100]

I think they were shooting .25 JSB's  in a .257 barrel. I don't see the .257 having enough power to do any good with slugs.

[usafvietnam]

I've owned the MAC35 for a couple years now. Owning #14  off the production line I have some good news and some, not so good. The first magazine that came with this rifle was suppose to hold 4 MAC's with the 5th in the chamber. The problem with the mag was that there was a design flaw and it would only hold three rounds. Okay, I guess I could live with that.  What I couldn't live with is that the MAC's would jam before loading into the breech. Not good. Inovairtech now tells me that they have a whole new design for it's mag now (I don't have the updated version).  And the MAC's are nortorious air leakers. I've had pellets pop off before even loading them into the mag.

AS OF SEPT. 2018 INOVAIRTECH IS OUT OF BUSINESS. THEIR WEBSITE IS REGESTERED TO BANKING/AIRLINE SITE.