P-Rifle on the way

[Papa T]

I think I read that someone has Troy at Big Air working on making mags. IIRC they will be 14 round mags.

I think that's for the pup, because that's the thread I read it in. Mags for barra 1100z work on P-Rifle though.

[bduares]

Anyone seen the guns on these pages? Some of them sure look similar to what Pinty sells

https://www.knivesdist.com/PELLET-GUNS_c_24.html

https://www.huntdowngears.com/air-guns/pellet-airsoft-guns/pellet-guns.html

[smythsg]

Folks, I ordered one of the Barra mags to try in the Bullpup but it will not fit. Happy to "Pay it Forward" to one of you folks that purchased the P-rifle if you need an extra mag!

[Papa T]

Folks, I ordered one of the Barra mags to try in the Bullpup but it will not fit. Happy to "Pay it Forward" to one of you folks that purchased the P-rifle if you need an extra mag!

I'd appreciate an extra mag if it's available.

[smythsg]

Terry was the first to reach out so the mag is yours. Send me a PM with your mailing address and I will get it on the way.

[Papa T]

Appreciate it, PM sent.

5 minutes after I left for work they delivered my rifle. This will be the longest Friday workday ever! 😞

[splitbeing]

Appreciate it, PM sent.

5 minutes after I left for work they delivered my rifle. This will be the longest Friday workday ever! 😞

[chuckling]
[shaking fist in frustration]

[splitbeing]

First impression: very good quality and excellent trigger. 

The urban has a worthy contender. My bet is on the P-Force at present.

[billygee]

Awesome,

Mines on it's way,
should be here next week

Following

Bill

[splitbeing]

Shroud off, Rocker1 on.

Nice looking externally adjustable hammer design.

[billygee]

Here's a Bullpup I've started to mess with 

[splitbeing]

Very good first day shooting. Cphps are a no go.  Out of the box they were going 915 avg witha 10ish ES over 30 shots. 

Here's the skinny: ftt 14.66 at 855 (24 fpe) is the sweet spot.

Details to come.

[splitbeing]

A handful of things to get on paper.

Shot count for ftts at 855ish fps avg fps with a tight enough ES and SD.

Downrange fps (a little less than 50 ft, chronographs tested and typically within a few fps or each other)

Downrange penetration of cigar tin stack (a little less than 50 ft)

[RichH]

Shroud off, Rocker1 on.

Nice looking externally adjustable hammer design.

So now the barrel is no longer tensioned?

[splitbeing]

Shroud off, Rocker1 on.

Nice looking externally adjustable hammer design.

So now the barrel is no longer tensioned?

The barrel screws in and is tight. When I go to take the moderator off, sometimes the barrel starts unscrewing and I have to hold it to unscrew the moderator and then twist it back tight.

[splitbeing]

Like the D48 at 16 fpe in .177 with ftts, the P-Rifle also got through two tins flush back to back at 24 fpe with ftts.

Another example of how a.177 pellet can penetrate much better than a .22 pellet at the same energy. RIP Shadow.

[RichH]

Shroud off, Rocker1 on.

Nice looking externally adjustable hammer design.

So now the barrel is no longer tensioned?

The barrel screws in and is tight. When I go to take the moderator off, sometimes the barrel starts unscrewing and I have to hold it to unscrew the moderator and then twist it back tight.

Exacly so it's no longer under tension. If you were to fashion an end piece to slip over the barrel with a shoulder that will slip into the original shroud I think you will see your accuracy improve.

[naptemp]

It seems that the shroud has a moderator adapter.
Why did you not put the moderator at the end of the shroud?

How is the original shroud working?

[Back_Roads]

  x2 

[RichH]

It seems that the shroud has a moderator adapter.
Why did you not put the moderator at the end of the shroud?

How is the original shroud working?

Because for some unknown reason the manufacturer made the barrel 1/2-20 but then made the shroud adapter 14mx1. So a 1/2-20 moderator will not screw onto a 14mx1 thread.