Pinty Tactical Airgun.

[TroyHammer]

These are the slugs I plan to shoot with My P-Force so these are the slugs I want to get the chrono numbers with and do any tuning accordingly. So far I have only been shooting this gun with these same BBT that I had on hand. I've probably shot 150 or so and the gun is deadly accurate with them out to 45 ish yards. I want to be sure I'm getting the same weight and accuracy out of this mold.
I've become very comfortable with the trigger and, as of now, don't plan to make any changes.

Dm me with an address. I'll send you a sear to test. Send me your factory sear if you like this one better. They'll be s return label for either sear you send back.

[avator]

These are the slugs I plan to shoot with My P-Force so these are the slugs I want to get the chrono numbers with and do any tuning accordingly. So far I have only been shooting this gun with these same BBT that I had on hand. I've probably shot 150 or so and the gun is deadly accurate with them out to 45 ish yards. I want to be sure I'm getting the same weight and accuracy out of this mold.
I've become very comfortable with the trigger and, as of now, don't plan to make any changes.

Dm me with an address. I'll send you a sear to test. Send me your factory sear if you like this one better. They'll be s return label for either sear you send back.

DM sent.
I got RS covered.. no need to include label.

[Back_Roads]

 I shot a couple different slugs today at 40 yards, needed alot of holdover for the 24 gr cup points I sized to .217, will size them down one more size and try again. The BBT .217 18.2 gr I cast in tin may have gone through the same hole a couple times

[avator]

SQUIRREL !!!
Yep, ole Rocky got me this morning.
I know I said I was going to wait for the new NOE 217 30 FN BBT mold to come before I chronied the gun but I just couldn't hold out one more day. 
I didn't want to burn through all the BBT slugs I have on hand because I want to use them for reference against the ones I drop from the new mold.
As happenstance would have it I recently received 4 fresh tins of JTS 18.1 pellets so I chose the to run a string.
Betty Lou called me to eat before I had a chance to import the numbers into the spreadsheet but that will come soon.
But I will say this...
From 3600 down to the 2100 reg setting it ran 70 shots in the window of 872 - 862. And every shot went into a 1" hole at 30 yds with a breeze blowing my target around.
This is straight out of the box setting... I ain't even cleaned the barrel on this gun.

[Back_Roads]

 Before brunch I ran some of my sized down slugs back through another sizer, and if Nick was done with mt Micrometer I would tell you exacts, but they seem to be in the .216 range after bringing down from .217. OE .218ish fresh cast. But same holing it at 10m, so whilr SHMBO an BIL are watching Lord of Ring Cartoon, I will go sneak in some Pating !!!

[avator]

Dang... took me awhile to remember how to use the spreadsheet.

I think some hammer spring adjusting is in order but it's close.

[Back_Roads]

 I see the up down spikes on the pressures above 3000, I hav noticed a few lower than adverage shots on mine at the higher pressure maybe below too. I suspect hammer binding, perhaps on the OE sear
 I was going to do some crony work with resized slugs but took a Squirrel Society Field Trip first LOL. See More on my Tube You Channel

[avator]

I'm gonna hold off on any adjustments until I get that mold tomorrow and run a batch of BBT slugs. I have a feeling that 12 more gr weight is going to slow those speeds down to mid 700s but FPE should increase if FPE matters to anyone. 30 FPE will obliterate anything I might shoot at around here. Oh and those HP BBT slugs really open up and would cut a large gap.
Those will be my go to ammo so that is what I will tune to.

[avator]

I see the up down spikes on the pressures above 3000, I hav noticed a few lower than adverage shots on mine at the higher pressure maybe below too. I suspect hammer binding, perhaps on the OE sear
 I was going to do some crony work with resized slugs but took a Squirrel Society Field Trip first LOL. See More on my Tube You Channel

I have yet to turn the first screw on this gun so, other than the pics that others have posted, I have now idea what the guts look like yet. I do know that there are a couple springs that will want to take flight so I will be watching for those.

[Back_Roads]

 I have not done anything but put a bit of preload on the hammer spring. I ran the slugs through my smallest sizer .2165 and got these numbers, and excellent accuracy.

BBT in tin 19gr. 805 fps

24gr cast cup point 710  fps

29gr BBT Lead 690 fps

[avator]

I have not done anything but put a bit of preload on the hammer spring. I ran the slugs through my smallest sizer .2165 and got these numbers, and excellent accuracy.

BBT in tin 19gr. 805 fps

24gr cast cup point 710  fps

29gr BBT Lead 690 fps

The mold is out for delivery.   

[avator]

I ran a batch of around 100 slugs with the long HP pins. After tumbling they averaged 27.5 gr <> .2. For some reason I thought those may be too light so I swapped to the medium pins and dropped another 50 or so.
While they were in the tumbler I tested the long pin sample. The fit the barrel really well and shot as accurate as the samples I have on hand.
The medium pin samples weight 30gr <> .5. I took those to the bench and the fit too snug in the barrel. I didn't force one in and dumped them back in the pot.
Long pin it will be. 
Cull rate was about 10% mostly due to me not filling out the mold. (Deforms)

[RichH]

Just saw the first one used to hit the classifieds, that was pretty quick

[avator]

Just saw the first one used to hit the classifieds, that was pretty quick

Yep saw that... probably a buy, try and sell type deal. I also saw it had a couple extras including a one pc. scope mount that I would never use on this gun. The extras brought the selling point up to $275. I passed.

[avator]

I poured, tumble and weighed up a couple hundred BBT slugs. Enough for a full tin. Now that the experimenting with the new mold is done I can drop that many in a couple short hours. I'm gonna keep going until I have a pt. Tupperware container full and try to maintain that in stock.
Next time Charles West calls me out to thin the Starlings that pester his Martin houses I'll be ready to lay them to waste. Yeah, I know... you don't need 35fpe to kill a Starling but I love seeing the poof of feathers. 

[Back_Roads]

I like it when the starlings go Pop!      I alike the solid points but I need to size them to get the best results.

[avator]

Today's casting session netted me about 400 pellets poured, tumbled and sorted/weighed/culled. I am very happy with the results.. 28gr <> .30. The P-Force is not picking with that tolerance at all. Cull rate was under 10%. I preheat the mold to 140c and run the pot at 700f and I ladle pour.

I have yet to run these over the chrono from the P-Force and the wind it a bit too high to do it today.. I like to shoot for consistent accuracy as I'm running the string. That's how I ran the JTS 18.1 and the entire 67 shot run hit minute of a squirrel noggin.

I don't know if anyone has noticed but you can shoot at different angles over the ProChrono and get different results. Angles will change the distance between the sensors. I've tested this with pellets that weighed exactly the same. So I like to aim at the same point throughout the string.

[bduares]

I shot my Chrony dead a few years ago. Now I use one that clamps on the barrel end

[Turk]

I don't have any experience with the Air Force guns so I can't relate but like I said... it puts me in mind of loading an underlever fixed barrel gun. Only difference is that it don't look like it has the potential to bite your finger off like those "Foo man chew" guns. 

Hi, i was wondering if you could help me with the pinty pcp because the manual is basically useless.i just got the pinty pcp tactical and i tried to remove the rubber pad underneath the barrel to install a foregrip. When i removed it a spring and metal piece popped out. Now i don’t know how to place back into gun. Also would you know the moderator thread size? Thanks in advance 🙏

[avator]

The threads are M14x1. I can't help you with the trigger sear and spring that fell out because I haven't had mine apart yet. I've seen the pictures that others posted but I doubt I could explain it just from those pictures, I do have a modified sear coming so I will be digging into it once that arrives.
I'm sure others with experience will soon chime in.