Author Topic: Pinty Tactical Airgun. (Read 10063 times))

TroyHammer · « **Reply #60 on:** February 22, 2025, 06:32:42 PM »

Quote from: splitbeing on February 22, 2025, 06:24:47 PM

Is the optics rail on the P-Rifle polymer or metal?

Metal on the tactical, I've not touched the others but have heard they are metal as well.

rkrr20307@comcast.net · « **Reply #61 on:** February 22, 2025, 06:46:23 PM »

The P-RIFLE scope rail is dovetail and is metal. If you purchase the P-RIFLE remove the trigger guard-2 screws- and 1 stock mounting screw and tighten all screws. Some where only hand tight on my rifle. Does not appear to have any plastic on rifled that I can see.

avator · « **Reply #62 on:** February 22, 2025, 07:17:56 PM »

I'm reading that some with the bullpup are saying the rail is weaver instead of picatinny. Anyone find a weaver on their PForce?

Robert 5mm · « **Reply #63 on:** February 22, 2025, 07:29:30 PM »

Quote from: avator on February 22, 2025, 07:17:56 PM

I'm reading that some with the bullpup are saying the rail is weaver instead of picatinny. Anyone find a weaver on their PForce?

Picatinny on mine

avator · « **Reply #64 on:** February 22, 2025, 07:31:26 PM »

Well that's good news.

splitbeing · « **Reply #65 on:** February 22, 2025, 08:06:33 PM »

Quote from: rkrr20307@comcast.net on February 22, 2025, 06:46:23 PM

The P-RIFLE scope rail is dovetail and is metal. If you purchase the P-RIFLE remove the trigger guard-2 screws- and 1 stock mounting screw and tighten all screws. Some where only hand tight on my rifle. Does not appear to have any plastic on rifled that I can see.

Thanks, Richard. Have one ordered and sooner or later on the way. Thinking a 2-7 hawke vantage. Fingers crossed it will like all these cphps I have lying around and accept the rocker1 I think is .22 compatible once I have the shroud removed to expose the 1x20 threads it's covering (different than the 1x14 endcap threads).

aluminumfetish · « **Reply #66 on:** February 22, 2025, 09:21:37 PM »

Quote from: Hoosier Daddy on February 22, 2025, 08:54:12 AM

Sorry, I am turned off after watching this video...
I will continue to save my coin for another TRUE Airforce Talon / Condor rifle to match my Texan.

What video ?

Papa T · « **Reply #67 on:** February 22, 2025, 09:32:52 PM »

Quote from: aluminumfetish on February 22, 2025, 09:21:37 PM

Quote from: Hoosier Daddy on February 22, 2025, 08:54:12 AM
Sorry, I am turned off after watching this video...
I will continue to save my coin for another TRUE Airforce Talon / Condor rifle to match my Texan.
What video ?

One by Inspire Precision further up in the thread.

Back_Roads · « **Reply #68 on:** February 23, 2025, 12:21:39 AM »

Meanwhile I finally had a chance to finish shooting this target that I started shooting when doing a video, just to have something to shoot at

I shot the top row then, and shot a couple more a few days ago, and finished today.
Single loading slows one down, but not that slow LOL 10m target holding over due to closer range.

Itching to give it the squirrel test

splitbeing · « **Reply #69 on:** February 23, 2025, 10:33:11 AM »

Anybody know if the p-rifle also has the huben reg?

avator · « **Reply #70 on:** February 23, 2025, 11:07:01 AM »

I doubt it.. wrong configuration. And from what I read from what Nick at Huben said, they just sent a batch of the bottle regs for the tactical gun.. least that's what I gleaned from the quote.
That said, I'm not even sure if there are any available for future runs of that gun. Might be a one and done thing.
Another good question for the folks at Pinty.

smythsg · « **Reply #71 on:** February 23, 2025, 12:16:11 PM »

Assuming the P-Rifle is a loose copy of the Snowpeak M-16 (which I owned two of) the reg is probably not Huben, but most likely Snowpeak. Huma sells an M16 reg that I installed in one of my rifles.

TroyHammer · « **Reply #72 on:** February 23, 2025, 12:19:36 PM »

Quote from: smythsg on February 23, 2025, 12:16:11 PM

Assuming the P-Rifle is a loose copy of the Snowpeak M-16 (which I owned two of) the reg is probably not Huben, but most likely Snowpeak. Huma sells an M16 reg that I installed in one of my rifles.

Huben verified this batch has authentic Huben regs.

smythsg · « **Reply #73 on:** February 23, 2025, 12:23:06 PM »

Troy, I assumed that the term "P-Rifle" was referring to the non Tactical rifle, sorry if I am incorrect.

TroyHammer · « **Reply #74 on:** February 23, 2025, 12:34:28 PM »

Quote from: smythsg on February 23, 2025, 12:23:06 PM

Troy, I assumed that the term "P-Rifle" was referring to the non Tactical rifle, sorry if I am incorrect.

My fault. I just went off the thread title being about the tactical. No knowledge of the other two models.

smythsg · « **Reply #75 on:** February 23, 2025, 12:38:18 PM »

No worries good sir, our new naming conventions gets confusing sometime...

This video shows the regulator in the Bullpup:

bduares · « **Reply #76 on:** February 23, 2025, 01:50:02 PM »

I didn't see the regulator in that video, but if it is similar at all to the P-35 then this video might help

]https://www.youtube.com/watch?v=IHc0ySIR-h0

smythsg · « **Reply #77 on:** February 23, 2025, 02:04:04 PM »

Hehe - in my video he did not call it a regulator, he called it a valve. He showed it completely disassembled with the washers laying next to the body.

Robert 5mm · « **Reply #78 on:** February 23, 2025, 05:53:22 PM »

Quote from: avator on February 21, 2025, 11:43:50 AM

A big shout out to THammer over on the AGN for allowing me to copy pics of his trigger sear mod to bring to this thread and share.
First off is the way the sear is from the factory...

And a comparison of before and after.

And a couple profiles of the finished sear layered on top of the factory.

This mod greatly reduces and smooths the trigger pull.

Be mindful, this mod will slightly increase the travel but I think he has a plan to address that too. I will share as I get more info.

I took out just the sear and polished it with 500 grit then 800 grit, but did not shape it like THammer.

Just the polishing the top and end of the sear that touch the hammer did make for a smoother trigger.

The only pin I had to bump half way out was the front pin, I left the rear one in.

Back_Roads · « **Reply #79 on:** February 23, 2025, 08:09:37 PM »

So
i did some slug test this afternoon, still grogy after my nap so there is that. I had a random bag of slugs I guess to be AVS dish base .217 24 gr they were consistent 730 fps, fit the bore maybe a bit loose, not the best IMO. On to some H&N 21 gr .218 these were a tight fit as seen in the photo they clocked at 790 fps and were much more on target. I think upping the reg set point would be needed to shoot slugs over 21 grain.
I am uploading the video, but have pics to post while we wait

Bottom row 21 grain H&N .218

Thank you to our advertisers!

Pinty Tactical Airgun.

Author Topic: Pinty Tactical Airgun. (Read 10063 times))