Pinty Tactical Airgun.

[avator]

A big shout out to THammer over on the AGN for allowing me to copy pics of his trigger sear mod to bring to this thread and share.
First off is the way the sear is from the factory...

And a comparison of before and after.

And a couple profiles of the finished sear layered on top of the factory.

This mod greatly reduces and smooths the trigger pull.

Be mindful, this mod will slightly increase the travel but I think he has a plan to address that too. I will share as I get more info.

[rkrr20307@comcast.net]

@Robert 5mm---Yes the barrel end is 14mm so did not fit in drill. I put loading end in drill about 3/8 turned and smoothed thin end then by hand finished last 3/8.

[TroyHammer]

It actually reduces travel.

[avator]

It actually reduces travel.

Oh ok, I must have read that wrong... anyways, thanks for sharing.

And feel free to add anything here you like.

[TroyHammer]

Turning down an AF barrel section just from the loading end up to where the first bushing would go on the factory barrel then boring the bushings to fit the AF OD allows for an Actual AF barrel to be fit.

[avator]

.22 or .25?

[TroyHammer]

.22 or .25?

That's still .22. I'm not sure the OD of the reduced section of the barrel in. 25 but the cocking section could easily be modified to accept either. I will likely convert mine to .177 for slugs.

[avator]

LOL... you're gonna make me want to start going to bed early and get up late so Tuesday comes faster..   

[splitbeing]

LOL... you're gonna make me want to start going to bed early and get up late so Tuesday comes faster..   

We call that time travelling here.

[Robert 5mm]

remove barrel assembly and spin it in  a drill with fine sand paper on thin area of barrel where it slides.

My drills have a maximum 1/2" drill bit. Is the muzzle end of this P-Force 14mm ( .55 inch )

Mine is out-for-delivery right now.

Just got mine, hard to cock, but closes OK.
Took off front grip spring dropped out, I think it goes in hole, then took off barrel.
No grooves on thinner front on barrel, so no need to spin and sand.

Now to put it back together, air up and shoot a few.

Now later edit:
Pushed a couple pellets thru barrel - I do not feel any choke.
Put it back together - aired to 3000psi ( 20 MPA = 2900 psi )

Shot a few without pellets - fairly loud in my garage.
Switched to a 14mm longer 3D printed suppressor - alot quieter.

Now let it sit over night at 18 MPA

[cosmic]

Well mine finally came, after getting lost in the vapor of Fedup !!! Fire a couple and then dismantled it .. The sear is on the way to Troy and I am now degreasing it..  I will dry lube it.. UTG compact coming..
                               Looks like fun...
                               (cosmic) Ray

[avator]

Depending on how my trigger is, I may need to schedule an appointment for it with Troy as well.

[Robert 5mm]

The tank on my P-Force was not even hand tight with the two gauges being level.
So I hand tightened the tank and rotated the butt stock to vertical, but the gauges are now not level.

How do you rotate the regulator or just the gauges ( and fill port ) back to level without loosening the tank ?
Maybe loosen regulator from gun frame ? and not M18 tank ?

The Long 3D printed suppressor is ALOT quieter than the short one that comes on the P-Force.
I downloaded it from Thingiverse and printed with PETG filament.

Here is a picture and name if you want to download the .STL file ( also Short version )
( I do not know if I legally can post the .STL file, so you have to get from Thingiverse ( it is free ).

[rkrr20307@comcast.net]

@Robert 5mm there is a grub screw that holds  the retaining collar that the tank/regulator screw into. Loosen grub screw to turn retainer to a position a tighten grub screw  when you tighten regulator to level it. Hope this  helps. I know because I removed retainer to get cocking lever out before I knew it will come out other end. Took me a couple times to get it reset. It should also have a mark from the grub screw you can set back where it was.

[rkrr20307@comcast.net]

Looks like that silencer has counter clockwise threads did it work on the P-FORCE ?

[Robert 5mm]

Looks like that silencer has counter clockwise threads did it work on the P-FORCE ?

Yes, it is the correct thread but tight on the suppressor, I did chase the thread with a M14x1 male tap.
The CCW thread is misleading, the CCW is if you are on the gun end and the suppressor screws CCW onto the barrel.
If you are on the muzzle end the suppressor screws on CW, just like a nut onto a bolt.

( I do not have a link for it - just go to Thingiverse and search for DX Silencer )

Thanks for the info on the grub screw. ( but I cannot find it )

There is a thread ( with Huben name on it ) inside the frame where the regulator screws into.
But is is not like the Air Force Spin Loc nut - that has a Spin Loc wrench.
And it does rotate a small amount - enough so I did get the gauges level.

[naptemp]

The tank on my P-Force was not even hand tight with the two gauges being level.
So I hand tightened the tank and rotated the butt stock to vertical, but the gauges are now not level.

How do you rotate the regulator or just the gauges ( and fill port ) back to level without loosening the tank ?
Maybe loosen regulator from gun frame ? and not M18 tank ?

The Long 3D printed suppressor is ALOT quieter than the short one that comes on the P-Force.
I downloaded it from Thingiverse and printed with PETG filament.

Here is a picture and name if you want to download the .STL file ( also Short version )
( I do not know if I legally can post the .STL file, so you have to get from Thingiverse ( it is free ).

The P-Force moderator seems to be very very short, and the volume is not enough to make it quiet

I remember printing the moderator you posted.
This is the link:
https://www.printables.com/model/1015678-air-gun-silencer-dx-m14ccw

[hoteltwofive]

YouTube review for those who haven’t seen it (no affiliation)

[avator]

So, what do y'all think about what he said about the tank stamp reading 4500 psi max fill? Would you go for it or do you think that the 3600 max recommended should be heeded?

[bduares]

I think he overlooked the possibility of things like a burst disc somewhere in the rifle, the main air tank may be rated higher but the rifle's other parts might object, and maybe the poppet would split under that sort of pressure...