Semi retired machinist looking for side jobs.

[Rick67]

Mr. Jay, would you be able to do a silencer front cap but in brass and with a concave front to save weight?

This one is a rear end cap (threaded hole) and would be more or less the shape.

Gracias 👍

[bear air]

Would you be able to cut a marauder tube and rethread it for a bottle gun. I'm mulling around an idea for a little longer short tube to increase my plenum on my 30 cal.

[IOWOLF]

Would you be able to cut a marauder tube and rethread it for a bottle gun. I'm mulling around an idea for a little longer short tube to increase my plenum on my 30 cal.

I don't do any thing with tanks.

  Tank you.

[Rick67]

Mr. Jay, would you be able to do a silencer front cap but in brass and with a concave front to save weight?

This one is a rear end cap (threaded hole) and would be more or less the shape.

Gracias 👍

I have a new AG I’d like to do some brass bling on and a silencer cap in brass would be a nice compliment.

[IOWOLF]

I would need the tube , or exact Dimensions.

[Rick67]

Exactly like the one in the photo.

It looks like a concave flashlight reflector.

I had them, brass and stainless, made by one of my machinist friends in the Philippines for my HW silencers.

Had access to more than a dozen as I was very much into the banana industry at that time.

[Mike71]

I would like a press on with set screw 1/2x28 adapter for a Crosman 2240.. mild steel.

 I can do it , Crosman Barrels are not all the same , You say press on , and with a set screw. First a press on that is a  tight fit and as barrels can vary .005" from barrel to barrel through out the years of Mfg. I would need your barrel to get a Press fit, then it is almost permanent. I would be happy to do it for you, the Price would be  $75.
Thanx.

Slip on fit I think would a better meaning, same as barrel dia and I'd sand till it just slips on with no slop.. I'll get some measurements tomorrow. That includes shipping right ?

[JP806]

Hi Jay
Here are the measurements for my TX200 spring guide.

Took me awhile to figure out how to post this...sorry for the delay.

[Mike71]

I would like a press on with set screw 1/2x28 adapter for a Crosman 2240.. mild steel.

 I can do it , Crosman Barrels are not all the same , You say press on , and with a set screw. First a press on that is a  tight fit and as barrels can vary .005" from barrel to barrel through out the years of Mfg. I would need your barrel to get a Press fit, then it is almost permanent. I would be happy to do it for you, the Price would be  $75.
Thanx.

Slip on fit I think would a better meaning, same as barrel dia and I'd sand till it just slips on with no slop.. I'll get some measurements tomorrow. That includes shipping right ?

Never mind. Went with a Buck Rail adapter and moderator setup. Got both for $65 shipped.

[IOWOLF]

I would like a press on with set screw 1/2x28 adapter for a Crosman 2240.. mild steel.

 I can do it , Crosman Barrels are not all the same , You say press on , and with a set screw. First a press on that is a  tight fit and as barrels can vary .005" from barrel to barrel through out the years of Mfg. I would need your barrel to get a Press fit, then it is almost permanent. I would be happy to do it for you, the Price would be  $75.
Thanx.

Slip on fit I think would a better meaning, same as barrel dia and I'd sand till it just slips on with no slop.. I'll get some measurements tomorrow. That includes shipping right ?

Never mind. Went with a Buck Rail adapter and moderator setup. Got both for $65 shipped.

Good , It pays to shop around.