Hey guys, I just wanted to mention I had an issue with a loose/wiggling picatinny rail and shroud on my new Notos. I found the issue to be that the screw that secures it was actually too long and was bottoming out before seating on the rail. I removed the screw and ground off 1-2mm and reinstalled it. plenty of threads to grab, and no more wiggle. I hope that helps someone else.
Hmmmm, never been b**** slapped by a DI, huh?
Did you check the Barrel set screw that is below the Rail set screw for tightness or proper alignment to the barrel set screw dimple? it might be loose or not aligned properly.
Charles, my Notos is averaging 20 ft lbs with the Apolo 18 gns and they are laser accurate out to 60 yards which is as far as I can test in my yard range. Hopefully yours will like them as well as mine does. I zeroed mine at 20 yards and it is dead on at 35 yards, easily squirrel head accurate with just under 16 ft lbs at 35 yards.
Thanks, JamesYou might have saved someone from overtightening their screws and stripping them, before realizing that they have the same problem. My guess is that someone at the factory grabbed the wrong length screws, used somewhere else, and that unless they compared them to the right ones, the extra length was not obvious.
I think if I had one of these I would go a different route than most. I think I would detune it to somewhere between 12 and 15 fpe. I don't hunt, I pest and I don't pest anything that requires more power than that within 35yds. to humanely dispatch.Although I am air independent with several options to fill the gun, shot count and accuracy are still the priorities for me. I prefer to spend more time shooting a gun than filling it.
Quote from: kbstingwing on August 18, 2023, 03:21:41 PMDid you check the Barrel set screw that is below the Rail set screw for tightness or proper alignment to the barrel set screw dimple? it might be loose or not aligned properly.Yes, I actually discovered this as I was checking the barrel screw. I was going to take the barrel out to check it out and clean it. I applied some force to remove the barrel, but it didn't budge. I decided to just leave it in for now since I had no real reason to take it out other than curiosity. That's a good point though, that if it were misaligned it could be causing the issue
Quote from: avator on August 23, 2023, 08:28:27 AMI think if I had one of these I would go a different route than most. I think I would detune it to somewhere between 12 and 15 fpe. I don't hunt, I pest and I don't pest anything that requires more power than that within 35yds. to humanely dispatch.Although I am air independent with several options to fill the gun, shot count and accuracy are still the priorities for me. I prefer to spend more time shooting a gun than filling it.I have 2 of those mods out the door: .3L bottle mods and aftermarket light hammer springs is all it took. The adjustment screw is good for 11-14 FPE.
Quote from: smythsg on August 22, 2023, 10:49:31 PMCharles, my Notos is averaging 20 ft lbs with the Apolo 18 gns and they are laser accurate out to 60 yards which is as far as I can test in my yard range. Hopefully yours will like them as well as mine does. I zeroed mine at 20 yards and it is dead on at 35 yards, easily squirrel head accurate with just under 16 ft lbs at 35 yards.Group testing will be next They look like they have potential so far. Thanks for sharing. I really like how Field Supply packages.
Quote from: Firewalker on August 23, 2023, 09:44:51 AMQuote from: avator on August 23, 2023, 08:28:27 AMI think if I had one of these I would go a different route than most. I think I would detune it to somewhere between 12 and 15 fpe. I don't hunt, I pest and I don't pest anything that requires more power than that within 35yds. to humanely dispatch.Although I am air independent with several options to fill the gun, shot count and accuracy are still the priorities for me. I prefer to spend more time shooting a gun than filling it.I have 2 of those mods out the door: .3L bottle mods and aftermarket light hammer springs is all it took. The adjustment screw is good for 11-14 FPE.I'm sure that's a great mod for many folks but I think for me I would lean more towards the lighter HS and TP size reduction to maintain factory appearance and not add weight. I probably shouldn't even be commenting on the gun because I have zero intentions of buying one. They are not my preference in style and I apologize for the negativity.
Is there some method of removing the moderator without destroying it ? Also, what does "CRK" mean ? I have a large collection of 1/2-20 UNF LDC's and would prefer using one of them and having the option of leaving it off.
Is there some method of removing the moderator without destroying it ? Also, what does "CRK" mean ? I have a large collection of 1/2-20 UNF LDC's and wouuld prefer using one of them and having the option of leaving it off.
Quote from: 7624452 on August 30, 2023, 07:52:16 PMIs there some method of removing the moderator without destroying it ? Also, what does "CRK" mean ? I have a large collection of 1/2-20 UNF LDC's and would prefer using one of them and having the option of leaving it off. Replace it an Artemis barrel that matches from WesBob He sells the Artimis LDCs drop shipped from California. https://airgunarcheryfun.ca/air-rifle-parts/
... Also, what does "CRK" mean ? ...
Advertise Here
Share This!