Author Topic: Ordered a mold (Read 4718 times))

Wayne52 · « **Reply #60 on:** March 05, 2022, 12:13:56 AM »

Matt they shoot excellent from my Liberty sized to .215, very accurate. The shoot awesome in my Challenger LS especially. They might shoot really good from Crosman rifles, especially the pcp's that can push them at a higher velocity. I tried them in my Crosman C362 sized .215&up but they're not good, I figure they're just not getting the push they need to be accurate.

Insanity · « **Reply #61 on:** March 05, 2022, 12:27:06 AM »

I have my urban and my nemmy my urban loves JSB hybrids I know these are not even close but maybe good enough to compare IDK. My nemmy has enough grunt to make them move because it was shooting 18gn pellets over 1000fps turned down from how I bought it used. So I think its set up from the PO to go much heavier at a good speed at that heavier weight. When I was testing it at Bakers the 25gn JSBs were moving 900fps on the same setting IIRC. Its been well over a year so thats all fuzzy.

Wayne52 · « **Reply #62 on:** March 05, 2022, 12:28:59 AM »

This is one of the neatest slug (BBT) recoveries that I've gotten. I was shooting from my Xisico Sentry (the one in my signature) I was using NOE 217-30-FN in hollow point that weigh about 27.5grains, this was recovered from a large chipmunk I shot straight on at about 30 yards, it entered through near it's left eye and was under the hide next to the tail on the opposite side of the chipmunk. The chipmunk literally flew back at least a foot and a half when it hit.

EdinGa · « **Reply #63 on:** March 05, 2022, 12:30:11 AM »

Quote from: Insanity on March 05, 2022, 12:27:06 AM

I have my urban and my nemmy my urban loves JSB hybrids I know these are not even close but maybe good enough to compare IDK. My nemmy has enough grunt to make them move because it was shooting 18gn pellets over 1000fps turned down from how I bought it used. So I think its set up from the PO to go much heavier at a good speed at that heavier weight. When I was testing it at Bakers the 25gn JSBs were moving 900fps on the same setting IIRC. Its been well over a year so thats all fuzzy.

My Urban loves my 30gr BBTs but it didn't Ike the NSA slugs I tried. I can't remember what weight they were.

Wayne52 · « **Reply #64 on:** March 05, 2022, 12:38:26 AM »

Ed I don't know if the Urbans are choked or not but if they're not it would probably shoot the NOE 218-25-RF good. They really are a wonderful slug out of the right gun.

EdinGa · « **Reply #65 on:** March 05, 2022, 12:44:57 AM »

I'm pretty sure it's choked but I could be mistaken. It's been on the back burner for awhile. My BBT mold is a .217 and it shoots great as cast.

Wayne52 · « **Reply #66 on:** March 05, 2022, 12:45:58 AM »

I'm have been tempted to buy a Challenger LS in 25 cal because I'm sure that it would be a devastating hunter at long distance with the NOE 250-39-RF in cup point.

EdinGa · « **Reply #67 on:** March 05, 2022, 12:49:20 AM »

Quote from: Wayne52 on March 05, 2022, 12:45:58 AM

I'm have been tempted to buy a Challenger LS in 25 cal because I'm sure that it would be a devastating hunter at long distance with the NOE 250-39-RF in cup point.

I've got that mold and it shoots well in my Flashpup, but I need something that will push it harder. Maybe one of the new JTS rifles.

Wayne52 · « **Reply #68 on:** March 05, 2022, 01:06:23 AM »

I recovered the slug from a fox squirrel I shot after the ground hog a few days ago, it basically went from head to close to the tail in the hide as well.

Insanity · « **Reply #69 on:** March 07, 2022, 05:23:12 PM »

218-25-rf in in house.

Insanity · « **Reply #70 on:** March 27, 2022, 07:43:34 PM »

Ordered these two molds.

250-27-RF-CC3 4 Cavity HB

250-34-RF-BR3 4 Cavity RG4 HB

EdinGa · « **Reply #71 on:** March 27, 2022, 07:46:46 PM »

Quote from: Insanity on March 27, 2022, 07:43:34 PM

Ordered these two molds.

250-27-RF-CC3 4 Cavity HB

250-34-RF-BR3 4 Cavity RG4 HB

I hope you have better luck with the 34 grain mold than some of us have.

Insanity · « **Reply #72 on:** March 27, 2022, 07:59:46 PM »

I dont know when Ill get around to casting and shooting them so time will tell. This is a fresh run so we will have to wait and see.

Spacebus · « **Reply #73 on:** March 27, 2022, 08:02:52 PM »

I'm thinking about ordering one of the 34 grain molds myself. Just cast 395 250-41-FN slugs out of pure tin. Much easier than lead!

Insanity · « **Reply #74 on:** March 27, 2022, 09:12:08 PM »

I am 85 dollars from the 1000 club.

Firewalker · « **Reply #75 on:** March 27, 2022, 10:37:10 PM »

Quote from: EdinGa on March 27, 2022, 07:46:46 PM

Quote from: Insanity on March 27, 2022, 07:43:34 PM
Ordered these two molds.

250-27-RF-CC3 4 Cavity HB

250-34-RF-BR3 4 Cavity RG4 HB

I hope you have better luck with the 34 grain mold than some of us have.

Sold mine off, didn't work in my guns.

scion19801 · « **Reply #76 on:** March 27, 2022, 10:51:15 PM »

I cleared the 1k club two orders ago. lol

Insanity · « **Reply #77 on:** March 27, 2022, 11:03:47 PM »

Nice gratz on that!

Insanity · « **Reply #78 on:** March 31, 2022, 08:29:59 PM »

Quote from: Insanity on March 27, 2022, 07:43:34 PM

Ordered these two molds.

250-27-RF-CC3 4 Cavity HB

250-34-RF-BR3 4 Cavity RG4 HB

These came in today they look great.

Spacebus · « **Reply #79 on:** March 31, 2022, 08:53:56 PM »

Let us know how it goes! I keep looking at pellet molds myself.

Thank you to our advertisers!

Ordered a mold

Author Topic: Ordered a mold (Read 4718 times))