Author Topic: Benjamin Maruader degassing tool dimensions (Read 1929 times))

click · « **on:** March 02, 2019, 10:51:49 PM »

Could anyone send me the dimensions of the Marauder degassing tool? Length, diameter and length of forward tip, diameter and length of larger main shaft?

I know the thread size already so don't need that. Thanks.

Chpmnkh8r · « **Reply #1 on:** March 03, 2019, 08:41:00 AM »

Here you go

Chpmnkh8r · « **Reply #2 on:** March 03, 2019, 08:50:18 AM »

Chpmnkh8r · « **Reply #3 on:** March 03, 2019, 08:51:15 AM »

Chpmnkh8r · « **Reply #4 on:** March 03, 2019, 08:52:44 AM »

Chpmnkh8r · « **Reply #5 on:** March 03, 2019, 08:55:19 AM »

Chpmnkh8r · « **Reply #6 on:** March 03, 2019, 08:59:14 AM »

Frank in Fairfield · « **Reply #7 on:** March 03, 2019, 10:40:27 AM »

Mechanics don’t bother with those things.
I saw motorhead stick a small rod into the hole and it is pushed against the valve stem....whoooosh!

CraigH · « **Reply #8 on:** March 03, 2019, 12:04:37 PM »

Quote from: Frank in Fairfield on March 03, 2019, 10:40:27 AM

I saw motorhead stick a 1/4” rod into the hole and it pushed against the valve stem....whoooosh!

Degasser? We don't need no stinking degasser!

kkarmical · « **Reply #9 on:** March 03, 2019, 12:45:06 PM »

If you have a hand pump you could just pump it up until check valve opens, then just open the bleeder a bit releasing the pressure that way.

click · « **Reply #10 on:** March 03, 2019, 02:02:54 PM »

Thanks chip!

Airgun-hobbyist · « **Reply #11 on:** January 30, 2021, 02:48:22 PM »

Does anyone if this tool de-gasses the new Benjamin Semi-auto? Also, what are the thread size?

vdwb · « **Reply #12 on:** January 30, 2021, 04:51:49 PM »

Quote from: Airgun-hobbyist on January 30, 2021, 02:48:22 PM

Does anyone if this tool de-gasses the new Benjamin Semi-auto? Also, what are the thread size?
[/quote

The end cap is the same as the Mrod’s, I will check to see if the length of the degassing tool is correct when I get home. The SAM is easy to degas by dry firing since you don’t have to continually cock it, just keep pulling the trigger until it full auto’s the hammer (low pressure) and then unscrew the gauge to release the last 50-100 psi remaining.

Dave S · « **Reply #13 on:** January 30, 2021, 07:16:54 PM »

The Degassing Rod Tim McMurray gave me for my Marauder was a 5" long .285" diameter....rusted rod with a handle that was hanging off his bench. He looked at me and said ," Here's your new de-gasser!"

Got home and cleaned it up on my wire wheel. and it stays in my Gun case.... A definite "Keepsake!"

dave

FuzzyGrub · « **Reply #14 on:** January 30, 2021, 07:30:25 PM »

I haven't tried the Mrod de-gasser tool in the SAM, yet. Given the short spring pocket, and inch shorter hammer spring, wondering if it may be too long for sam.

Nachi · « **Reply #15 on:** February 22, 2024, 02:26:35 PM »

Hi there.
Can anyone tell me the thread size & type of thread for the P-Rod Degasser?

Thanks in advance.
Regards,
Nachi

Frank in Fairfield · « **Reply #16 on:** February 22, 2024, 02:55:20 PM »

Look at the back of your rifle.
Not sure?
Take the rifle to Ace Hardware.

lm22 · « **Reply #17 on:** February 22, 2024, 08:52:33 PM »

can always just unscrew the gauge a little as well.

Nachi · « **Reply #18 on:** February 23, 2024, 12:49:13 PM »

Quote from: Frank in Fairfield on February 22, 2024, 02:55:20 PM

Look at the back of your rifle.
Not sure?
Take the rifle to Ace Hardware.

Sorry Frank but I live in Malaysia where carrying anything that looks remotely like a "GUN" even a life sized toy imitation will land u in jail so walking into ACE Hardware is definitely out of the question

Nachi · « **Reply #19 on:** February 23, 2024, 12:52:09 PM »

Quote from: lm22 on February 22, 2024, 08:52:33 PM

can always just unscrew the gauge a little as well.

Hi Liam, I'm just worried about stripping the threads & having the gauge fly across the room or thru a glass window. I will have a lot of explaining to do to the Missus

Thank you to our advertisers!

Benjamin Maruader degassing tool dimensions

Author Topic: Benjamin Maruader degassing tool dimensions (Read 1929 times))