Author Topic: refurbed titan (Read 7733 times))

3ants · « **on:** July 09, 2011, 04:36:28 PM »

got my refurbed titan yesterday i think it might be of the last run of the crosman titan now they are benjie titans anyway same problem with the pivot screw bushings barrel lose side to side going to get some of genes brass bushings and a gas ram bushing this gun is a lot different than the one i got at wallyworld last year. the chps fit the barrel tighter and you would not belive how the trigger feels almost perfect will know more after i get the barrel bushings repaired it shoots pretty good now at 15 steps ever thing looked good little ding here and there kindof wish i had bought 2 of them

one_shot · « **Reply #1 on:** July 09, 2011, 04:44:23 PM »

i picked up a titan refurb a few mths ago......it was better than the 4 titans i returned to walmart.
i love my refurb.

Collier · « **Reply #2 on:** July 09, 2011, 06:47:23 PM »

I finally got some pellets so I could shoot mine today. Working on the break in period so far. Like yours, a few dings in the stock but nothing bad.

3ants · « **Reply #3 on:** July 09, 2011, 06:52:13 PM »

collier how is your trigger?

dkwflight · « **Reply #4 on:** July 09, 2011, 07:32:06 PM »

Hi

I just got one of the refurbed titans.
It seems fine.
I have tech force wad cutters in .22
they don't seat deep enough so the skirts are damaged on closing.
I made a pusher to seat the pellets deeper.
I will have to run the chrony and see if it is more consistent.
Dennis

Collier · « **Reply #5 on:** July 10, 2011, 12:49:10 AM »

Quote from: 3ants on July 09, 2011, 06:52:13 PM

collier how is your trigger?

Between my son and I we have around 100 shots, so it isn't broken in yet, and not too quiet yet, but not bad. Most of my shooting was trial and error trying to find how the gun groups with different holds. I seem to do best with an artillery type hold, but a little more support with the shoulder and cheek. Doing that, I got one group under 1/2" at 50'. Not earth shaking, but not too bad so far. Just figured out that hold, so I will try some more shooting tomorrow. I'm sure a CDT trigger will be a help, but the factory trigger is a little better than the Daisy/Gamo springer we have.

3ants · « **Reply #6 on:** July 10, 2011, 10:00:51 AM »

collier thats better groups than i am getting my target is probly 45-50 feet my groups are getting better with chps, crosman ultra mags i put a 3-9- 32 scope off one of my other airguns it helped you may be able to see better than me, i shot about 15 prediter poly mags in it this morning probly 3/4 of an inch or less its not broke in yet the other pellets started out about 6 inch group now there down to about 3 inch group ordered some of the brass washer for the pivot screw from gene yesterday that will make a big inprovment

DanBrothers · « **Reply #7 on:** July 10, 2011, 10:19:49 AM »

I just got a Crosman titan GP..with a center 3-9 scope...for 60.00.... from a pawn shop ...it shoots pretty good with CP's...haven't tried for tight groups yet...

I did loosen the muzzle break and pulled it all the way out until the set screws where just biting the last 1/2" of the barrel... and it did make it alot quieter...

I could have bought two of these same guns for the same price.... but let the other one slip away... dang...

At 25 - 30 yds.. I can keep a 1" spinner looking like a fan blade...

3ants · « **Reply #8 on:** July 10, 2011, 11:08:46 AM »

your cats sound like mine fresh meat out there but they like dry cat food sounds like you got a good buy on your titan

Collier · « **Reply #9 on:** July 10, 2011, 04:01:10 PM »

I was trying to get this thing dialed in this morning, and got pretty frustrated, then noticed the scope mounts had shot loose. Tightened everything up and it is keeping shots on a 1" target dot, most toward the inner ring. I am shooting Cabelas hollow point pellets until it settles down. I did get a tin of RWS, so will try them a bit later. Trigger pull is very long, but consistent. Would be tough to shoot offhand, but by the time I start doing that and expecting good results, I should have a CDT unit in it. DanBrothers, congrats on the great deal.

z28rod · « **Reply #10 on:** July 11, 2011, 08:25:58 AM »

Collier , just wait till you get that tuna trigger, I put my Titan away cause I got so tired of dealing with a 12lb trigger, Installed Charlie's trigger and it was night and day difference. Now its right on and fun to shoot for hours and try to get a better and better group. Try cphp pellets, see how they group.

Collier · « **Reply #11 on:** July 12, 2011, 12:34:18 AM »

Was confused by the GP/NP thing. Mine is a GP. but C8, so I guess it is high power?

A few days of shooting it destroyed our pellet trap, so I am searching for a better one. This gun reminds me of my Marlin 22. Very accurate at times, but pretty inconsistent. I guess the trigger would help, but I'd like to see some consistency before I get one.

3ants · « **Reply #12 on:** July 12, 2011, 07:37:03 AM »

check your barrel for side to side movement the pivot screw on mine was a little lose i ordered a set of genes brass pivot bushings $6.00 shipped they make alot of differents if you tighten the screw and still have a little movment they will fix the problem

z28rod · « **Reply #13 on:** July 12, 2011, 11:15:16 AM »

"Mine is a GP. but C8, so I guess it is high power?"
Can someone explain this to me ? Is it a serial number thing or what ?

dkwflight · « **Reply #14 on:** July 12, 2011, 02:15:43 PM »

Hi
I seem to get the best accuracy with .177 H&N Barracuda greens.
They are some alloy and harder than the lead pellets.

3ants · « **Reply #15 on:** July 12, 2011, 09:10:15 PM »

hi, got excited about my new titan it is a better gun than a year ago out of the box got my old titan out new one wont shoot with it or my xl, but soon it will strarting to improve pivot bushings trigger re crowning the breach all an all you cant beat the price for the qaulity even if it needs some modifeing dont know yet if it will stay a 22 or put this new 177 barrel on it ( titan dusk to dawn 177) open sights too

randomgunner · « **Reply #16 on:** July 13, 2011, 02:41:10 PM »

no, it means the power of the gas ram. the "C7 gas ram is the lower powered version, and it has lowered cocking effort. the "C8" gas ram in the high powered one, which also has higher cocking effort, but personally i find the cocking effort very light, i feel as though you have to be a midget to not cock it.

3ants · « **Reply #17 on:** July 13, 2011, 08:04:10 PM »

hi going to change the name of my titan refurb to (titan dawn to dusk ) it has open sights with the phantom barrel i installed it today at work dont really no a lot of results yet but it is fairly acurate only 177 pellets it seams to like that i have is h and n 7.10 gr it shooting them 1050-1059 i will get some chps in the morning going to work if i dont have any work i will break it in, pictures later camera went crazzy

xXcrosmanhunterXx · « **Reply #18 on:** July 13, 2011, 08:34:25 PM »

Quote from: z28rod on July 11, 2011, 08:25:58 AM

Try cphp pellets, see how they group.

I thought that Crosman made the Hollow Points for Cabela's, and Cabela's just threw their name on the tin?

3ants · « **Reply #19 on:** July 14, 2011, 08:36:53 AM »

collier there is a screw at the back of the stock trigger if it is not screwed down you might adjust it for a shorter trigger travel,if you turn it 1/2 turn at a time you might see a change

Thank you to our advertisers!

refurbed titan

Author Topic: refurbed titan (Read 7733 times))

3ants

Collier

3ants

dkwflight

Collier

3ants

DanBrothers

3ants

Collier

Collier

3ants

dkwflight

3ants

randomgunner

3ants

3ants