Any US importers carrying this gun?

[cosmic]

Definitely need one for my .177 that  darkcharisma is working on for me...

[Back_Roads]

 It is the same probe as the Senica Aspen.

[Bob Pratl]

A photo and the probes dimensions would be most helpful in order to fabricate one.

[darkcharisma]

My liberty came this morning but I only got just the rifle with that $107.50 deal they had, whats a good source for a probe for these guns.

Wayne, If you ran out of options such as calling ATI and ordering from PA. I am more than willing to turn and make one for you out of o1 steel. you just need to pay for shipping.

[kgatwork]

My liberty came this morning but I only got just the rifle with that $107.50 deal they had, whats a good source for a probe for these guns.

Gamo Urban Probe works great!

[RDB]

My liberty came this morning but I only got just the rifle with that $107.50 deal they had, whats a good source for a probe for these guns.

I swore i read somewhere in this thread the Urban fill probe works on the liberty.

[Wayne52]

Rod I ordered a BSA fill probe that's also suppose to work, it's got the foster connect so I won't need an adapter.

[USAFANG6799]

Gamo Urban Probe works great!

I swore i read somewhere in this thread the Urban fill probe works on the liberty.

My replacement Liberty2, which I called it, also came without a probe which makes it virtually useless a pcp air rifle. On recommendation I was told that a BSA/Urban probe would work until I got mine from ATI, which took about what felt like a month but think it was like two week +-.
It didn't quite work because the probe was too long. The diameter was ok. I was able to jeary rig-it by adding two orings on the probe itself to mark how far to insert the probe into fill the tube. Not something I recommend though but used it to at least check to make sure it would not leak air like my Liberty1.

This is the one I ordered:BSA GAMO DYNAMAX SCORPION HORNET ULTRA R10 1/8 BSP STAINLESS FILL PROBE & SEALS.

Maybe it was the wrong one?

[Wayne52]

Matt when I get the probe I'll measure the depth of the orifice of the hole in the hole in the gun and go from there.  My brother did the same thing with a Varmint using a long probe, just added a sleeve to restrict the depth of the probe after it was inserted.

[USAFANG6799]

Matt when I get the probe I'll measure the depth of the orifice of the hole in the hole in the gun and go from there.  My brother did the same thing with a Varmint using a long probe, just added a sleeve to restrict the depth of the probe after it was inserted.

Yep essentially what I did but used orings.
I added "not recommended" because folks where encountering instances where the hose would kick back if the probe was not seated properly. Just a caution.

[tracker1955]

Hi guys, after about a week of testing with various pellets I can say with confidence that the Liberty likes lubed pellets. Although the Liberty wasn't pellet picky out of the box it did prefer certain pellets over others for max accuracy. Although my Liberty at this time is giving me the best groups with JSB 15.89's, even the cheap CPD's are grouping better than they ever did pre-lube. I can't say yet at this time if it will prolong the time between needed cleanings, but it has made a definate improvement in group sizes of pellets that didn't make the initial cut. I was getting great enjoyment dancing a small poly pill bottle around at 55 yards using the cheap $8.00 per tin Crosman premier dome untra magnums I'd picked up at Tractor Supply.

[Bob Pratl]

Hi guys, after about a week of testing with various pellets I can say with confidence that the Liberty likes lubed pellets. Although the Liberty wasn't pellet picky out of the box it did prefer certain pellets over others for max accuracy. Although my Liberty at this time is giving me the best groups with JSB 15.89's, even the cheap CPD's are grouping better than they ever did pre-lube. I can't say yet at this time if it will prolong the time between needed cleanings, but it has made a definate improvement in group sizes of pellets that didn't make the initial cut. I was getting great enjoyment dancing a small poly pill bottle around at 55 yards using the cheap $8.00 per tin Crosman premier dome untra magnums I'd picked up at Tractor Supply.

What lube did you use and how did you apply it?

[cosmic]

Well I don't post much since mine is a .177, but a bit of information.. The first 6" of the barrel on mine was super tight..  Check yours out..Started at 4.52 and then chambered and removed.. 4.35 as close as I can measure ... Still working the barrel to help that.. Try pushing a pellet through and feel where it gets easier at.. Mark that place on your cleaning tool of your choice and work that area over with some compound.. ( JB or fine lapping compound )
   I heard they were tight but mine seems waaaaaaaay tight...

[RDB]

How are your regs working out? I wasn't overly impressed the way mine was performing. Eve adjusted to the knee it seemed to wander quite a bit.

Ordered some Bellevilles from McMaster Carr and from the 30 or so pellets I shot adjusting it back to the knee. It's working much better. Let it set for 3 hours and its still right on the money. Hate having to wast a shot to even everything up. Not good for hunting situations. I did polish the brass piston rod and sand the seat on a flat surface before hand. But the washers have seemed to do the trick. They are a bit taller than the stock ones, so they do have more range of motion. Backed the reg off 3 dots to get where i previously was.

Part #96445k215 if anyone want to give them a shot

[tracker1955]

Hi guys, after about a week of testing with various pellets I can say with confidence that the Liberty likes lubed pellets. Although the Liberty wasn't pellet picky out of the box it did prefer certain pellets over others for max accuracy. Although my Liberty at this time is giving me the best groups with JSB 15.89's, even the cheap CPD's are grouping better than they ever did pre-lube. I can't say yet at this time if it will prolong the time between needed cleanings, but it has made a definate improvement in group sizes of pellets that didn't make the initial cut. I was getting great enjoyment dancing a small poly pill bottle around at 55 yards using the cheap $8.00 per tin Crosman premier dome untra magnums I'd picked up at Tractor Supply.

What lube did you use and how did you apply it?

I used an empty pellet tin with foam in the bottom filled with aprox 100 pellets and spayed them with Blaster silicone spray from Home Depot, added the lid and rolled and flipped the can for a few minutes to spread the lube and let foam pull off any excess. Magazines were loaded with the tumbled pellets that now had a nice film on them and shot normally. I have a spray bottle of Napiers coming from Amazon but it hasn't shown up yet. I may not have ordered it if I'd tried the Blaster first.

[kzz1kaw]

How are your regs working out? I wasn't overly impressed the way mine was performing. Eve adjusted to the knee it seemed to wander quite a bit.

Ordered some Bellevilles from McMaster Carr and from the 30 or so pellets I shot adjusting it back to the knee. It's working much better. Let it set for 3 hours and its still right on the money. Hate having to wast a shot to even everything up. Not good for hunting situations. I did polish the brass piston rod and sand the seat on a flat surface before hand. But the washers have seemed to do the trick. They are a bit taller than the stock ones, so they do have more range of motion. Backed the reg off 3 dots to get where i previously was.

Part #96445k215 if anyone want to give them a shot

Thanks for the heads up👍🏾 Don’t like wandering regulator pressures either😎 use their bellville washers in my Frankenstein 2240 gun and works great

[kzz1kaw]

Hi guys, after about a week of testing with various pellets I can say with confidence that the Liberty likes lubed pellets. Although the Liberty wasn't pellet picky out of the box it did prefer certain pellets over others for max accuracy. Although my Liberty at this time is giving me the best groups with JSB 15.89's, even the cheap CPD's are grouping better than they ever did pre-lube. I can't say yet at this time if it will prolong the time between needed cleanings, but it has made a definate improvement in group sizes of pellets that didn't make the initial cut. I was getting great enjoyment dancing a small poly pill bottle around at 55 yards using the cheap $8.00 per tin Crosman premier dome untra magnums I'd picked up at Tractor Supply.

What lube did you use and how did you apply it?

I used an empty pellet tin with foam in the bottom filled with aprox 100 pellets and spayed them with Blaster silicone spray from Home Depot, added the lid and rolled and flipped the can for a few minutes to spread the lube and let foam pull off any excess. Magazines were loaded with the tumbled pellets that now had a nice film on them and shot normally. I have a spray bottle of Napiers coming from Amazon but it hasn't shown up yet. I may not have ordered it if I'd tried the Blaster first.

Pic of the blaster can

[tracker1955]

Was going to post before but am waiting for the picture from my phone to show up in my email where I can save it to my pictures, not sure why it's taking so long to show up in Gmail.

[tracker1955]

I use my phone because I can take the picture and size it all in one step then send to my mail, have sent it three times and none of them have shown up yet.

[Lastdog]

Was it JB Blaster?