Author Topic: Bulldog modification log .328 porting and more (Read 39763 times - 1 votes)
)

Kinetic45^ · « **Reply #300 on:** December 31, 2018, 04:08:09 PM »

@PCPhack
Got my SS valve in today ( QUICK shipping from JSAR and during the holidays too!) and wanted to ask you where you sourced the .015 jet. I went to both Auto(ripoff)zone, O'Riley's and Advance Auto parts with the 'OEM' SS jet and asked for the .015 you described in an earlier post and they all just we're blank... They can "look it up if you tell them what car it fits" but have no way in their computers just for parts... dumb programming and over reliance on computers. Just knownothing kids behind the counters.
It can be looked up if they have a part number but they don't have a jet size list EITHER!
Looked on Internet and places like Amazon and I generally have good search-fu but skunked out.

MJP · « **Reply #301 on:** December 31, 2018, 04:21:33 PM »

Motorcycle shops man!

oldpro · « **Reply #302 on:** December 31, 2018, 05:37:00 PM »

Set of jet drills and solder.

Coyote · « **Reply #303 on:** December 31, 2018, 05:39:59 PM »

Quote from: oldpro on December 31, 2018, 05:37:00 PM

Set of jet drills and solder.

Thanks!

PCPhack · « **Reply #304 on:** December 31, 2018, 06:14:37 PM »

Yep, solder the end up and then drill it to the size you want. I initially used a needle, but then got these bits. Just convert from mm, as we are talking about inches (mils) on these jet sizes, if you buy a metric set.

UEB Mini twist drill Bit Kit, 0.4mm-3.2 HSS Micro Precision Twist Drill 150Pcs with Carry Case for PCB Crafts Jewelry Drilling Tool

PCPhack · « **Reply #305 on:** December 31, 2018, 09:01:28 PM »

Factory dogbone link for reference. It is also ferrous/sticks readily to a magnet.

rsterne · « **Reply #306 on:** December 31, 2018, 10:30:19 PM »

David, to do a "column buckling" analysis, you also need the length between the load points.... That should be between the holes at the sides closest to each other.... It looks like the pins on both ends are the same size (1/8")

Bob

Kinetic45^ · « **Reply #307 on:** December 31, 2018, 11:04:13 PM »

Quote from: oldpro on December 31, 2018, 05:37:00 PM

Set of jet drills and solder.

+ Thanks

I hate a growing monopoly but have to love Amazon: Ordered for Wednesday delivery. Actually ordered both sets posted by OldPro and PCPhack as I'm sure I need them somewhere

PCPhack · « **Reply #308 on:** December 31, 2018, 11:09:51 PM »

Quote from: rsterne on December 31, 2018, 10:30:19 PM

David, to do a "column buckling" analysis, you also need the length between the load points.... That should be between the holes at the sides closest to each other.... It looks like the pins on both ends are the same size (1/8")

Bob

Thought I posted it. Hmm. 1.23 inches, closest 2 points.

Happy New Year!

rsterne · « **Reply #309 on:** January 01, 2019, 12:24:54 AM »

I used a "column buckling" calculator and got a maximum supported load of 798 lbs for a "pinned" column.... so that works out to a safety margin of about 2.7 at 3000 psi, or only about 1.8:1 at 4500 psi, using mild steel for the material for the link.... IMO that means the factory link should not be used above the 3000 psi recommended pressure....

I don't know how your longer link compared in thickness, however....

Bob

PCPhack · « **Reply #310 on:** January 01, 2019, 01:15:17 AM »

The longer one was just to test a bit. It's in the trash already.

I don't want to guess on metal Benjamin used, but either they are OK with lower safety margins, or the guesses here on steel type are wrong. Like before, for economic reasons, you are likely right. Perhaps after I get my hands on some heavier duty parts from JSAR, we can do some tests to better determine metal type of these factory ones.

ShakySarge · « **Reply #311 on:** January 01, 2019, 01:21:46 AM »

Just to break it up a bit................

Happy New Years!!!!!

PCPhack · « **Reply #312 on:** January 01, 2019, 01:39:46 AM »

Happy New Year!!! Lol @ Loosy Moosy. Ughhhh, why do I know that.

ShakySarge · « **Reply #313 on:** January 01, 2019, 01:46:01 AM »

Quote from: PCPhack on January 01, 2019, 01:39:46 AM

Happy New Year!!! Lol @ Loosy Moosy. Ughhhh, why do I know that.

LMBO!!!! Who knew right?!!!!

Been doing some shop work for the linkage issues, figured tonight would be a good break!!!

Kinetic45^ · « **Reply #314 on:** January 01, 2019, 03:11:07 AM »

Quote from: ShakySarge on January 01, 2019, 01:21:46 AM

Just to break it up a bit................

Happy New Years!!!!!

AAAHHHHHGGUUUUHHHHH!!!!!!!!!
MONSTER!!!!!!! BIGFOOT!

{What? No copied PIC?}

You need some HUNTER SAFETY ORANGE, you could get shot, haha

ShakySarge · « **Reply #315 on:** January 01, 2019, 05:08:46 AM »

"That dang Samsquanch!!!!!"

PCPhack · « **Reply #316 on:** January 01, 2019, 03:53:39 PM »

To complete the documentation... here is the front dogbone link pin. This looks like a typical industrial steel dowel, complete with beveled end, ferrous, etc.

.125 inch diameter

Kinetic45^ · « **Reply #317 on:** January 01, 2019, 11:19:50 PM »

I don't know if any of you have been following my thread on the Darkside about Chairgun and Strelok Pro but Igor/Strelok has added drag functions: GA (pellets), GL (blunt like pistol bullets) and GS (round ball) for me.
Talked to him about Airguns vs PB needs yesterday and it updated today, he's quick!

rsterne · « **Reply #318 on:** January 02, 2019, 01:15:38 AM »

NICE !!!....

Bob

Tonycalves · « **Reply #319 on:** January 02, 2019, 02:24:44 PM »

Nice! That's in the payed version though not free? Might have to invest

Thank you to our advertisers!

Bulldog modification log .328 porting and more

Author Topic: Bulldog modification log .328 porting and more (Read 39763 times - 1 votes) )

Author Topic: Bulldog modification log .328 porting and more (Read 39763 times - 1 votes)
)