1720T & Compact Adjustable Marauder Pistol Stock

[screwwork]

Hi guys,

Here are the first photos of Lees aka (Vash545) Compact Adjustable Marauder Pistol Stock 
The assembly is a nice as Lee said it would be, light, compact easy to adjust and install.
I like the Compact Adjustable Marauder Pistol Stock without the cheek riser for my gun, it shoulders great, good scope height for me too
I noticed when shooting my 1720T with the (CAMPS) Compact Adjustable Marauder Pistol Stock it was flexing the as I had a pressed into my shoulder hard to stop me from moving around, it will take a little time to get used to my new way of steading my sights with the carbine.
No point of impact from lighter hold in shouldered position. I really like this stock, it is so much better then the factory stock!

Lee it was a pleasure to business with you and let me know if you come out with a PP700 stock please.

Randy

Here are a few glamour shots.






1720T with Rocker 1 LDC combos.








 

[Dairyboy]

Very nice Randy looks great! Posted mine in the original thread got it on my Prod and I love it!

[screwwork]

Nice looking Prod Dillon 
Also you beat me to posting the first photo of the new stock, so I am the second person to photo a of Lee's new stock by 13 ish minutes! LOL

[LeE]

Hi guys,

Here are the first photos of Lees aka (Vash545) Compact Adjustable Marauder Pistol Stock 
The assembly is a nice as Lee said it would be, light, compact easy to adjust and install.
I like the Compact Adjustable Marauder Pistol Stock without the cheek riser for my gun, it shoulders great, good scope height for me too
I noticed when shooting my 1720T with the (CAMPS) Compact Adjustable Marauder Pistol Stock it was flexing the as I had a pressed into my shoulder hard to stop me from moving around, it will take a little time to get used to my new way of steading my sights with the carbine.
No point of impact from lighter hold in shouldered position. I really like this stock, it is so much better then the factory stock!

Lee it was a pleasure to business with you and let me know if you come out with a PP700 stock please.

Randy

Here are a few glamour shots.






1720T with Rocker 1 LDC combos.

Thank you for sharing the "money shots". The stock integrates really well with your setup (and looks really slick with the after market LDC!). I hope you found the installation easy and straightforward (I will be posting a pictorial on the main post to clear up any confusion). There is a little play in the stock to strike a balance between sturdiness and ease of extending/retracting the stock. The stock guides are lubed before being shipped out. If the stock feels stiff, a little grease will help. Like what you have found, a lighter hold from my testing has no impact on accuracy.

[ackuric]

Looks great guys. Very impressed with this idea, hope you pick up more models and keep pumping these out!

[Bizill]

Gentleman, I'm LOVING how low you've got your scopes mounted because the aftermarket stock allows for it.

[Dairyboy]

Nice looking Prod Dillon 
Also you beat me to posting the first photo of the new stock, so I am the second person to photo a of Lee's new stock by 13 ish minutes! LOL

Lol barely got ya beat then! Looks great with all your Rocker1 goodies 

[screwwork]

Gentleman, I'm LOVING how low you've got your scopes mounted because the aftermarket stock allows for it.

Bill,
I use the med height rings on the all aftermarket and on Crosman skeleton stocks.
I like my scope as low as possible.

Randy

[Dairyboy]

Gentleman, I'm LOVING how low you've got your scopes mounted because the aftermarket stock allows for it.

Bill,
I use the med height rings on the all aftermarket and on Crosman skeleton stocks.
I like my scope as low as possible.

Randy

+1

[Mr. Panther]

Nice looking love it.

[LeE]

Gentleman, I'm LOVING how low you've got your scopes mounted because the aftermarket stock allows for it.

Bill,
I use the med height rings on the all aftermarket and on Crosman skeleton stocks.
I like my scope as low as possible.

Randy

The stock was designed to allow the same rings that were being used before the stock was installed. The magazines sits higher than the dovetail mounting block.

[LeE]

Looks great guys. Very impressed with this idea, hope you pick up more models and keep pumping these out!

Which models would you like to see supported?

[ackuric]

Looks great guys. Very impressed with this idea, hope you pick up more models and keep pumping these out!

Which models would you like to see supported?

I'm not a pistol owner but there are many more on market that I am sure would benefit, just not sure there is a big enough community of them! Other than that (just hoping you flourish) I am sure some rifles would love the adjust-ability of the stock this provides!

[LeE]

Looks great guys. Very impressed with this idea, hope you pick up more models and keep pumping these out!

Which models would you like to see supported?

I'm not a pistol owner but there are many more on market that I am sure would benefit, just not sure there is a big enough community of them! Other than that (just hoping you flourish) I am sure some rifles would love the adjust-ability of the stock this provides!

Thank you for your kinds works of encouragement. I was thinking about doing something for the MRod but there is the queston of what the market will bear with needing to make an adapter for a pistol grip and the handguard. The cost would be in the mid $200's.

[FuzzyGrub]

Looks great guys!  Great work Lee.   I'd bet it is much sturdier than some of those non-retracting wire stocks I've seen. 

[ackuric]

Looks great guys. Very impressed with this idea, hope you pick up more models and keep pumping these out!

Which models would you like to see supported?

I'm not a pistol owner but there are many more on market that I am sure would benefit, just not sure there is a big enough community of them! Other than that (just hoping you flourish) I am sure some rifles would love the adjust-ability of the stock this provides!

Thank you for your kinds works of encouragement. I was thinking about doing something for the MRod but there is the queston of what the market will bear with needing to make an adapter for a pistol grip and the handguard. The cost would be in the mid $200's.

Yea, maybe at some point down the road maybe you could come up with a concept for mrods and see what kind of interest there is! For around 200 and change I think it would be a very competitive option to the others out there, which are very limited imo. A refined minimized stock is quite desirable to me!  Turn the now 43" marauder into a potentially 32"-42" marauder with adjustable stock seems appealing to me!

[screwwork]

I would like to see a Mrod AR adaptor that replaced the stock end cap! Short, sweet, offset so it would be inline with the top of tube. It would use a Prod pistol trigger package along with a new sear from Lloyd.
Lee, let me know if you a napkin drawing!   

[screwwork]

Also a Compact Adjustable PP700 Pistol Stock!
That would be awesome.

[Dairyboy]

Doing stocks on other platforms would be great! I really love mine!

[LeE]

I would like to see a Mrod AR adaptor that replaced the stock end cap! Short, sweet, offset so it would be inline with the top of tube. It would use a Prod pistol trigger package along with a new sear from Lloyd.
Lee, let me know if you a napkin drawing!

No napkin drawing yet. Just a thought and an image of what I see in my mind of what it would look like. If people are happy to use a Prod trigger pack with grip, I'd be happy to provide a stock and not worry about designing a grip. There is the question of the handgaurd. Would users be ok with no handgaurd on their Mrods?

I like the idea of replacing the OEM endcap/hammer preload housing with an adapter for an AR15 stock. It would shorten the whole package and be more rigid. Good stuff!! I will add it to my list of things to design.