eBay compressor

[kzz1kaw]

This is my overview of the yong heng compressor video on you tube. I was filling a 144cc suba tank in stages. First stage empty was 30 minutes plus 5 minutes that didn't get timed = 35 minutes. Second stage to 4500 psi = 46 minutes. I don't recommend filling a large scuba tank all though this compressor will fill the tank, I recommend doing it in stages. This compressor is good for filling an empty airgun cylinder or topping off a tank from 1k to 3 k or 3 k to 4.5 k. Yes I would recommend buying one😎

[kzz1kaw]

During the fill process, I experimented with ice packs in the bucket of water which help bring the water temperature down for the air pump. Approximate fill time in stages for 144 cc tank is 81 minutes +/- 5

[redtrucker610]

Any more reviews on how these compressors are holding up?

[kzz1kaw]

Any more reviews on how these compressors are holding up?

I have been using this compressor since my last review with no problems at all. Glad I bought one👍🏾

[imadunatic]

Ken,

What is a 144 CC tank? That seems tiny to me since a 13ci ninja is 213cc.

I'm considering one of these to top off my scuba after each shooting session (3000 PSI 80 CF, maybe ~200 psi top off) but if it takes an hour to fill a bottle half the size of a ninja bottle, that might not be quite enough....

[kzz1kaw]

Ken,

What is a 144 CC tank? That seems tiny to me since a 13ci ninja is 213cc.

I'm considering one of these to top off my scuba after each shooting session (3000 PSI 80 CF, maybe ~200 psi top off) but if it takes an hour to fill a bottle half the size of a ninja bottle, that might not be quite enough....

Good question. That is what it says on the tank. It is a large tank though. It took over an hour to fill from empty. filling a tank from 2000 psi will not take an hour. Hope this helps

[imadunatic]

Is it like a 30 minute or a 45 minute type tank? I found a relevant discussion here mentioning the 144cc, I'm thinking that might explain it?

Even if it's a 30 minute, that is still fairly impressive for such a small pump, though I believe I'd want a high pressure side filter if I go this route and that would probably add a fair bit of time to the fill process.

[Killfire]

I have the Tuxing with a little over an hour and a half run time on it so far. I've filled my marauder a couple times and completely filled a Guppy tank. Impressions are good but it isn't a plug and go compressor.
 
Anyone buying one should un screw EVERYTHING that screws to the outside and Teflon tape the threads. At 2000+ PSI a small leak may be imperceptible but it's definitely reflected on fill times.

A set of metric allen keys is a must.

A high side separator/drier is a good idea. Mine tends to purge quite a bit of water and I don't trust the tampon filter.

You can't boost the inlet from a shop compressor. It stalls the motor.

My plastic fan on the back of the motor walked itself into the mounting frame and started to shred itself. It's only held in place with some C clips and there isn't a grove on both sides of the motor shaft to retain it.

Also all the screws are a soft material. I plan on picking up some that are a bit harder.

All in all I'm happy with my purchase. Does anyone know where I can get a fairly inexpensive high side filter?

[kzz1kaw]

I have the Tuxing with a little over an hour and a half run time on it so far. I've filled my marauder a couple times and completely filled a Guppy tank. Impressions are good but it isn't a plug and go compressor.
 
Anyone buying one should un screw EVERYTHING that screws to the outside and Teflon tape the threads. At 2000+ PSI a small leak may be imperceptible but it's definitely reflected on fill times.

A set of metric allen keys is a must.

A high side separator/drier is a good idea. Mine tends to purge quite a bit of water and I don't trust the tampon filter.

You can't boost the inlet from a shop compressor. It stalls the motor.

My plastic fan on the back of the motor walked itself into the mounting frame and started to shred itself. It's only held in place with some C clips and there isn't a grove on both sides of the motor shaft to retain it.

Also all the screws are a soft material. I plan on picking up some that are a bit harder.

All in all I'm happy with my purchase. Does anyone know where I can get a fairly inexpensive high side filter?

Bought a diablo air filter from  r&l airuns $179

[redtrucker610]

I have been corresponding with a seller Chon electronic technologies on aliexpress about the yong heng. I have asked about upgrading the oil/water separator to a larger one. The said they could upgrade to the large one for addition $80. I don't have a tank yet so I would be using it to direct fill my Marauder for now. I just haven't convinced myself to order one yet. This would be about $450 with the shipping. I just worried about how long these will last.

[kzz1kaw]

I have been corresponding with a seller Chon electronic technologies on aliexpress about the yong heng. I have asked about upgrading the oil/water separator to a larger one. The said they could upgrade to the large one for addition $80. I don't have a tank yet so I would be using it to direct fill my Marauder for now. I just haven't convinced myself to order one yet. This would be about $450 with the shipping. I just worried about how long these will last.

Yes it is the roll of the dice. My omega super charger is made in China along with other name branded compressors.  I am using this compressor almost every day filling just my airguns because it is portable. I don't need a tank to fill up. I just fill the gun. My omega is sitting as a backup and no it's not for sale😎

[Killfire]

I didn't see the Diablo filter on the website or one from Chon.

[kzz1kaw]

I didn't see the Diablo filter on the website or one from Chon.

Aoa has them on their website

[Killfire]

I didn't see the Diablo filter on the website or one from Chon.

Aoa has them on their website

Ah I found one on Ali that I ordered already. They look to be about the same outside though.

[Tims229]

The important part of the high pressure moisture filters is that they are strong enough to handle the pressure as they will need to withstand up to 4500 psi in most cases.  I have the Diablo filter and the wall of that filter is around one inch thick or more.  It is built very stout to withstand those kind of pressures.  This is not an area you want to go on the cheap with as a failure in that part of your system would be a bad day for you or anyone in the immediate area. 

[kzz1kaw]

I didn't see the Diablo filter on the website or one from Chon.

Aoa has them on their website

Ah I found one on Ali that I ordered already. They look to be about the same outside though.

Do you have a link? I want to buy another one for my omega compressor

[Killfire]

I didn't see the Diablo filter on the website or one from Chon.

Aoa has them on their website

Ah I found one on Ali that I ordered already. They look to be about the same outside though.

Do you have a link? I want to buy another one for my omega compressor

Here you go,
https://m.aliexpress.com/s/item/32602913439.html?trace=wwwdetail2mobilesitedetail&productId=32602913439&productSubject=This-is-a-gift-free-of-mechanical-parts-the-link-is-used-for-customers-pay-the&spm=2114.13010608.0.0.VnEK5u#autostay

Looks like extra tampons $3 for 5. Someone mentioned somewhere that they take a standard filter insert size. Can anyone elaborate on that? Dimensions or links to different replacement media? Thanks.

[kzz1kaw]

I didn't see the Diablo filter on the website or one from Chon.

Aoa has them on their website

Ah I found one on Ali that I ordered already. They look to be about the same outside though.

Do you have a link? I want to buy another one for my omega compressor

Here you go,
https://m.aliexpress.com/s/item/32602913439.html?trace=wwwdetail2mobilesitedetail&productId=32602913439&productSubject=This-is-a-gift-free-of-mechanical-parts-the-link-is-used-for-customers-pay-the&spm=2114.13010608.0.0.VnEK5u#autostay

Looks like extra tampons $3 for 5. Someone mentioned somewhere that they take a standard filter insert size. Can anyone elaborate on that? Dimensions or links to different replacement media? Thanks.

That is the diabolo  air dryer system but in red anaodized coloring😳 Thanks I'll order one.

[elguapo99]

I just ordered one of the Xin Yong Shi filters on the 15th and it is scheduled for delivery on the 24th. My hand pumps are their brand and they also arrived quickly and have been flawless. I plan to cut the tampon into two pieces to use on the ends and fill the middle with desiccant beads. It may require a PVC liner of some kind to keep the desiccant from contacting and eating away at the aluminum housing. I think the Diablo filter uses molecular sieve type desiccant. Does anyone know if the Diablo has a liner inside?

[kzz1kaw]

I just ordered one of the Xin Yong Shi filters on the 15th and it is scheduled for delivery on the 24th. My hand pumps are their brand and they also arrived quickly and have been flawless. I plan to cut the tampon into two pieces to use on the ends and fill the middle with desiccant beads. It may require a PVC liner of some kind to keep the desiccant from contacting and eating away at the aluminum housing. I think the Diablo filter uses molecular sieve type desiccant. Does anyone know if the Diablo has a liner inside?

No liner just the housing