Smaller-sized PCPs

[Bridger3]

Agt vixen short light weight and will love your 18.1 pellets

[Xraycer]

My mail to Pyramyd just now:

I bought the Notos based on your recommendation.

It leaks, out of the box. It stops filling at about 2200 PSI - you can hear the leak. Then, when the probe is removed, it sags down to about 1500 (barely in the green).

I'd already taken the time to mount & bore-sight a scope. I should've tested the gun first.

Very disappointed.

Put some 100% silicone oil onto the center of the fill probe, and then refill the gun. Mine did that initially. I now do this after every 10 fills or so.

[PaulFWI]

My mail to Pyramyd just now:

I bought the Notos based on your recommendation.

It leaks, out of the box. It stops filling at about 2200 PSI - you can hear the leak. Then, when the probe is removed, it sags down to about 1500 (barely in the green).

I'd already taken the time to mount & bore-sight a scope. I should've tested the gun first.

Very disappointed.

Put some 100% silicone oil onto the center of the fill probe, and then refill the gun. Mine did that initially. I now do this after every 10 fills or so.

I always lube the probe o-rings. That's not it. (My FX Wildcat uses a similar probe and doesn't have such issues.)

There are reports all over the net of these things leaking out of the box. I'll give Pyramyd a chance to fix it, otherwise it goes back.

[Xraycer]

My mail to Pyramyd just now:

I bought the Notos based on your recommendation.

It leaks, out of the box. It stops filling at about 2200 PSI - you can hear the leak. Then, when the probe is removed, it sags down to about 1500 (barely in the green).

I'd already taken the time to mount & bore-sight a scope. I should've tested the gun first.

Very disappointed.

Put some 100% silicone oil onto the center of the fill probe, and then refill the gun. Mine did that initially. I now do this after every 10 fills or so.

I always lube the probe o-rings. That's not it. (My FX Wildcat uses a similar probe and doesn't have such issues.)

There are reports all over the net of these things leaking out of the box. I'll give Pyramyd a chance to fix it, otherwise it goes back.

I'm not referring to lubing the probe's o-rings. Apply a liberal amount of silicone oil to the center of the probe where the air exits. This causes a spray onto the o-ring in the air tube when the air is pushed in.

[PaulFWI]

My mail to Pyramyd just now:

I bought the Notos based on your recommendation.

It leaks, out of the box. It stops filling at about 2200 PSI - you can hear the leak. Then, when the probe is removed, it sags down to about 1500 (barely in the green).

I'd already taken the time to mount & bore-sight a scope. I should've tested the gun first.

Very disappointed.

Put some 100% silicone oil onto the center of the fill probe, and then refill the gun. Mine did that initially. I now do this after every 10 fills or so.

I always lube the probe o-rings. That's not it. (My FX Wildcat uses a similar probe and doesn't have such issues.)

There are reports all over the net of these things leaking out of the box. I'll give Pyramyd a chance to fix it, otherwise it goes back.

I'm not referring to lubing the probe's o-rings. Apply a liberal amount of silicone oil to the center of the probe where the air exits. This causes a spray onto the o-ring in the air tube when the air is pushed in.

Ah, Ok. Sorry - I didn't get it.

So the other thing is that today my 7-8 yo Nomad compressor died! Pumping my Impact after the Notox, it gave up the ghost. So I can't try this just yet.

[Xraycer]

So the other thing is that today my 7-8 yo Nomad compressor died! Pumping my Impact after the Notox, it gave up the ghost. So I can't try this just yet.

Dang, that's a bad day! I've had those kind of days more than I care for.