GTA

All Springer/NP/PCP Air Gun Discussion General => PCP/CO2/HPA Air Gun Gates "The Darkside" => Topic started by: DRose on February 17, 2023, 08:39:06 PM

Title: Nova Vista Freedom fill probe
Post by: DRose on February 17, 2023, 08:39:06 PM
I destroyed my onboard pump years ago. No parts to repair it. So I thought I could still fill it with a fill probe, and shoot it, (was a good shooter) but never had a probe. Pyramyd air is out of Seneca Aspen probes. Anyone know of another source? Don't care if factory or not. Thanks
Title: Re: Nova Vista Freedom fill probe
Post by: Back_Roads on February 17, 2023, 10:18:06 PM
 I will dig mine out tomorrow, and measure, but this one looks darn close to what is needed.
https://www.ebay.com/itm/403944329498? (https://www.ebay.com/itm/403944329498?)
(https://i.ebayimg.com/images/g/y6oAAOSwhGZgi8H0/s-l1600.jpg)
Title: Re: Nova Vista Freedom fill probe
Post by: DRose on February 17, 2023, 10:30:16 PM
Looks right. I use my Gamo Urban probe to fill the other Nova Vista pcps. Thanks!
Quote from: Back_Roads on February 17, 2023, 10:18:06 PM
I will dig mine out tomorrow, and measure, but this one looks darn close to what is needed.
https://www.ebay.com/itm/403944329498? (https://www.ebay.com/itm/403944329498?)
(https://i.ebayimg.com/images/g/y6oAAOSwhGZgi8H0/s-l1600.jpg)
Title: Re: Nova Vista Freedom fill probe
Post by: Wayne52 on February 18, 2023, 03:20:23 AM
For my Liberty I use the same probe that my Sentry's take.  It works fantastic on both the Sentry and the Liberty, it's made from steel instead of brass too.
Title: Re: Nova Vista Freedom fill probe
Post by: Back_Roads on February 18, 2023, 10:10:59 AM
 The freedoms fill port is deep under the pump handle, so the long narrow probe is needed, unique to the Nova- Vista line. OK measured 7.5ish od, had to measure with a bolt gauge as my calipers are @ werk, ::) of the probe end by orings. 70mm long or there abouts. I would feel confident that it will work , or just needs some sanding in a drill, with fine paper to get it just right.
Title: Re: Nova Vista Freedom fill probe
Post by: fatmike on February 18, 2023, 12:05:06 PM
The liberty has a different fill probe then the freedom. I bought a freedom dill probe for my li erty when pa had them and it's to loose. I massaged the op about the one I have for a freedom that doesnt work on my liberty. Hopefully he replies.
Title: Re: Nova Vista Freedom fill probe
Post by: Hawkeye51 on February 18, 2023, 12:39:31 PM
David
After buying fixing and selling several freedom parts guns, I know that there was a run of guns with a different length probe. Good idea to measure the depth of your fill port, just to be sure.
Title: Re: Nova Vista Freedom fill probe
Post by: DRose on February 18, 2023, 03:24:55 PM
Thanks guys. Looks like a &^^& shoot at best. I'll get the long probe and try it out. Dave
Title: Re: Nova Vista Freedom fill probe
Post by: Madd Hatter on February 19, 2023, 03:22:57 PM
Quote from: Wayne52 on February 18, 2023, 03:20:23 AM
For my Liberty I use the same probe that my Sentry's take.  It works fantastic on both the Sentry and the Liberty, it's made from steel instead of brass too.
Liberty is a whole different cart of apples.