GTA
Airguns by Make and Model => Vintage Air Gun Gate => Topic started by: ped on June 17, 2020, 02:44:43 PM
-
a few years back i had some brass loading gates made but wasn't going to have any more made
a good friend on your side of the pond asked for a few so i'm haveing 5 made and if there is demand i'll have more made
until i get them i have no idea on cost and you'll have to get your own insert
-
I will take at least four. Thanks. :D
-
no probs i'll increase this current order
i'm not sure on cost as yet though
-
Are the loading gates themselves all the same size, and the inserts are what determine the calibers- or does the loading gate itself determine the caliber? Did that make sense? I wouldn't mind getting two of these. ;D
-
gates are all the same size and it is the inserts that determine caliber
i've doubled the order to 10 with 7 provisionally accounted for once i have them in my hand i'll have a price for them and those who expressed an interest will have first refusal
-
I have all 3 sizes of inserts. Email me if you need them. Please send your complete mailing info to get shipping cost with order. Not just zip. peter_built 78@hotmail.com
151A024 .177 $4.25 each
151A224 .20 $2.00 each
151A124 .22 $2.00 each
plus shipping
-
Gentlemen, you have made me an extremely happy person!!! I thank you!
-
I have all 3 sizes of inserts. Email me if you need them. Please send your complete mailing info to get shipping cost with order. Not just zip. peter_built 78@hotmail.com
151A024 .177 $4.25 each
151A224 .20 $2.00 each
151A124 .22 $2.00 each
plus shipping
Hi Mike. I just emailed you about your inserts. If you don't see it, check your spam. AOL often goes there.
Forgot to mention in the email that I'm looking for .177 only.
Dennis :D
Mike - UPDATE - My AOL send did not go though. I resent it via the email link here in GTA.
Let me know if you get it.
Thanks,
Dennis :D
-
Ped - I'll take six of them.
Dennis :D
-
currently only 3 left unspoken for but once this first batch is made and all is good i'll get another run done Dennis, i will though see if the order can be increased
Mike would it be possible to get a few of each inserts shipped to the UK as i have a few inserts i'm just not sure where they are ,and whilst i can make them from ptfe it's easier use genuine ones
i have in the past have had bits from you but it was a long time ago and i did hear you'd stopped shipping out of the US
-
I will take at least four. Thanks. :D
I need (5) five. Thanks.
-
currently only 3 left unspoken for but once this first batch is made and all is good i'll get another run done Dennis, i will though see if the order can be increased
Mike would it be possible to get a few of each inserts shipped to the UK as i have a few inserts i'm just not sure where they are ,and whilst i can make them from ptfe it's easier use genuine ones
i have in the past have had bits from you but it was a long time ago and i did hear you'd stopped shipping out of the US
If I can get in on those unspoken-for three, that would be sufficient for now. I really don't need six.
Dennis :D
-
when i have the first batch ready i'll people know and will order more
-
Most Excellent!! Many thanks
-
Ped,
We corresponded last year on this and you told me none were available. I am thrilled to hear this news. I would like two gates please.
Thank You
-
i was quite suprised when my mate who makes them agreed to do them as originally he wasn't going to do anymore
looks like i better try to get him to do 20
-
i was quite suprised when my mate who makes them agreed to do them as originally he wasn't going to do anymore
looks like i better try to get him to do 20
If the order quantity you propose to him becomes a deal breaker, then I only NEED one. If it is not a problem then I will buy two for future use.
Thank you
-
If the order quantity you propose to him becomes a deal breaker, then I only NEED one. If it is not a problem then I will buy two for future use.
Thank you
X2!!
-
i'll see what he says but i'm happy to up th order if he has time to do them
-
I have all 3 sizes of inserts. Email me if you need them. Please send your complete mailing info to get shipping cost with order. Not just zip. peter_built 78@hotmail.com
151A024 .177 $4.25 each
151A224 .20 $2.00 each
151A124 .22 $2.00 each
plus shipping
Mike, two .177 inserts received yesterday. Thank You, didn't think I would ever see one of those again if the one I have gets lost.
Guys,
Mike was terrific to do business with. I did not read directions correctly for using Paypal and stiffed Mike $1 on my $12 order. I asked how I should make it right and Mike told me not to worry about it. I inquired into another purchase which I would tack the dollar onto but he did not have any SSP 250 .20 barrels.
I hope that by putting in an especially good word here will make up for mistake until I can make it right.
-
I'll second Mike's sales performance. I ordered 12 of the .177 inserts I have like 8 of the 1389's, plus the one that my son owns). Great to have these available.
Ray - Did you get the white Delrin(?) inserts or the old amber waxy type? Those old ones deteriorate.
:D
-
I'll second Mike's sales performance. I ordered 12 of the .177 inserts I have like 8 of the 1389's, plus the one that my son owns). Great to have these available.
Ray - Did you get the white Delrin(?) inserts or the old amber waxy type? Those old ones deteriorate.
:D
Got the white ones!
-
i've doubled the order for the gates to 20 so they'll be enough for all who have expressed an interest
-
HUZZAH!!!
-
Thank you ped, very much!!
PM me for price and shipping info and I'll send you some $$ right away.
Dennis :D
-
Thank You ped
-
all being well i should be picking 20 gates up at the end of next week
10 are ready now and the others will be ready by the time i can drive over and collect them
-
Ooohhh, shucky duck!! I can't wait!
-
Awesome news!
For those of us on this side of the pond would it make any sense to get them all shipped to one of us and then reship to save on overseas shipping?
-
that wouldn't be an issue to me and would save on postage
-
I am interested in a couple too if I can fit/squeeze in now.
-
Awesome news!
For those of us on this side of the pond would it make any sense to get them all shipped to one of us and then reship to save on overseas shipping?
I could certainly take care of this if everyone was in! Let me know.
-
Awesome news!
For those of us on this side of the pond would it make any sense to get them all shipped to one of us and then reship to save on overseas shipping?
I could certainly take care of this if everyone was in! Let me know.
I'm down!
-
all being well i should be picking 20 gates up at the end of next week
10 are ready now and the others will be ready by the time i can drive over and collect them
I am interested in a couple too if I can fit/squeeze in now.
If you have 2 more I am at the back of the line now, LOL
-
Awesome news!
For those of us on this side of the pond would it make any sense to get them all shipped to one of us and then reship to save on overseas shipping?
I could certainly take care of this if everyone was in! Let me know.
I would be fine with that but since I am at the back of the line I don't want to hold anyone up either. I haven't heard if the line was cut off in front of me? So there is that too!
-
I have all 3 sizes of inserts. Email me if you need them. Please send your complete mailing info to get shipping cost with order. Not just zip. peter_built 78@hotmail.com
151A024 .177 $4.25 each
151A224 .20 $2.00 each
151A124 .22 $2.00 each
plus shipping
Thanks Mike, my order has been made and payed. I didn't think anyone was selling any .177 or .20 anymore.
-
i'll be picking up 20 gates on Mon i'll be going through the list of what people would like and in what order tomorrow so i can acertain how many are surplus or if i need to inc the order again
-
i'll be picking up 20 gates on Mon i'll be going through the list of what people would like and in what order tomorrow so i can acertain how many are surplus or if i need to inc the order again
Did I make it on the list for 2, or was I too late? I did not see where or how much to pay.
-
i've not gone through how many have been asked for as yet Dan
price wise they'll be around £17.50 each plus post
if i need to order more to cater for the couple you'd like i'll do so on Monday so don't worry we'll be able to acommodate you
-
i've not gone through how many have been asked for as yet Dan
price wise they'll be around £17.50 each plus post
if i need to order more to cater for the couple you'd like i'll do so on Monday so don't worry we'll be able to acommodate you
Thanks, I will be/am patient! Let me know how and when to pay, upfront would be fine with me by the way.
-
this is my list
3 gates for my mate
7624452 5 gates
yemx 2 gates
stinger 177 6 gates
superchikn 2 gates
rabbit squirrel killer 2 gates
total 20 gates
-
That is correct for me.
-
correct-o-mundo!
-
I went through the list too, looks like I snuck in just under the wire. 8) ;D
I need payment info. and it is OK with me if mine goes/ships threw superchikn to save on overseas shipping since he offered. When the time comes I will need to know shipping payment info from Ray too. I will pay as soon as I have/see the info because I don't want to hold anyone up by not being timely. 8) 8) 8) ;D
Awesome news!
For those of us on this side of the pond would it make any sense to get them all shipped to one of us and then reship to save on overseas shipping?
I could certainly take care of this if everyone was in! Let me know.
-
I'll second Mike's sales performance. I ordered 12 of the .177 inserts I have like 8 of the 1389's, plus the one that my son owns). Great to have these available.
:D
I'll third Mike's sales performance. I ordered 10 total of the .177, .20, .22 inserts. I have 4 of the 1389's, plus the one SSP250. My SSP already has a NICE brass loader and it is great to find these. If there is another batch of the brass loaders in the future and I see it I may get a couple of more to take care of the other two 1389's that won't get one this round. If not a least I will have spare plastic loaders.
-
My last .20 insert broke a year ago and I have been unable to shoot my favorite SSP-250. I really appreciate Mike and Ped making these items available. Thanks.
-
Ped - Sent you a PM with my shipping info and invoice request.
Whenever you get around to it, I'm ready to pay.
Thanks again!!
Dennis :D
-
got it Dennis i'm away tomorrow for a week fishing so i'll not be able to post till i get back
i'll get another 10 ordered Dan so i have stock and will be able to supply you some more
if all who are happy haveing theirs shipped to Superchikn can let me know and i'll sort that out as postage may be more on that parcel
price will be £17.50 per gate and from what i can tell postage will be around £12 for int signed and tracked but i'll get a better idea when i have parcel weight
-
I'm perfectly fine with shipping to superchikn first... Should make things easier- 1 port of entry, then re-verify shipments in the States before shipping out. Me likey!
-
these are them and i've just done a bit of random testing with a new insert i had to hand i'll want to do a random test fit to a gun all so
-
*whistles* Beauty!
-
these are them and i've just done a bit of random testing with a new insert i had to hand i'll want to do a random test fit to a gun all so
Looks good and even though it is not a clone of the plastic original it is the function that is most important. The big unnecessary "handle" on the original design is not good if you put an optic on it and this design would be better in that case. 8)
Again to be clear, I am an OK on the shipping to Superchikn.
-
if there any left over I'd go for one gate and 2 inserts for a 22 cal. I just today put a 14" barrel in and hog'd out the bung/insert to take a 22.
It was a .177 and is not mine, still belongs to it's og owner. he says he bought it when he was 17 ? and is now 52. He broke the plastic loader soon after buying and it sat until last summer, we got another plastic loader and ebay bung/insert in .177. of course the 177's where a pita to handle. I shot it over the green speedometer it gave a 499 fsp by shot #5 was down to 450 fsp and as loud as a rimfire 22
-
hi Jab another run of 10 is being made so i can accomodate you one
i had pm'd you to say it would be a week or so but i can let you have one from this batch as my good friend who i iniatially was having them made for would like a couple more as would another gentleman he is good mates with so i'll send his from the new run being made
i'll be pm'ing every one with price and paypal addy and if all who would like to take up Superchikn's offer of having there's sent to him for him to forward on could let me know
-
i think i have pm'd everyone with costs and postage prices
if i have missed anyone please pm me
-
packageing will be here today so i'll be parcelling up tonight and getting them ready to ship