Author Topic: AA S400 MPR FT Came In!!!! (Read 37223 times))

mista meener · « **Reply #20 on:** June 04, 2014, 04:20:52 PM »

Quote from: Rdsail on June 01, 2014, 10:17:56 PM

My AA is a FT gun and being set up for FT. 25 yards is the zero. At this point I'm just starting with my setup. I will only stretch out to 55 yards due to Field target. The mrod that is on my signature will shot MOA to 1.5 MOA at 100 yards and the disco will shot under moa at 70 yards. In my home range I can only shot up to 40 yards. I wish I could shot my mrod and my Custom disco 50 plus yard more often.

Now that is what I am talking about lol. Your mrod is great at 100 and the disco is also at 70. My AT44 10 shoots about half inch at 50 and my disco comes close and that is with crosman wal mart pellets.

mista meener · « **Reply #21 on:** June 04, 2014, 04:22:12 PM »

Quote from: azoutdoorsman on June 02, 2014, 12:56:49 AM

Quote from: mista meener on June 01, 2014, 09:50:11 PM
Quote from: azoutdoorsman on June 01, 2014, 07:40:38 PM
Wow, very nice! What reticle does your scope have?

My Mueller has 8-32x has a mildot reticle, I wish it were a little finer. Here are a couple of groups using the scope on a .25 Marauder at 25 yards:

I'm going to start my own thread now, thanks for the inspiration!
Come on guys 25 yds is not a test for those rifles lol. Let the rifles stretch their legs and take them out to 50- 75 yds . Love to see the results

My yard is small!

Time to get real friendly with someone who has some land lol

Rdsail · « **Reply #22 on:** June 04, 2014, 04:45:05 PM »

I check all the distances on the scope wheel and I was a little off specially in the farther ends of the focus. I made adjustments and now a right on. New picture.

I also got my new case for this gun. The middle layer gets cut out for a perfect fit. Plano All weather.

Now I just need to wait for the side wheel. I was able to shoot 40 yards today and the accuracy is right on. It is more accurate than my custom disco when the wind does not blow the pellet.

And if you can notice. I made the spacers not the palm rest longer. I need the extra height when shooting from seating position.

Rdsail · « **Reply #23 on:** June 04, 2014, 07:43:32 PM »

Today is UPS day. I just got the knock down targets. Now I don't have any excuse not to practice.

azoutdoorsman · « **Reply #24 on:** June 04, 2014, 07:44:46 PM »

Quote from: Rdsail on June 04, 2014, 04:45:05 PM

I check all the distances on the scope wheel and I was a little off specially in the farther ends of the focus. I made adjustments and now a right on. New picture.

I also got my new case for this gun. The middle layer gets cut out for a perfect fit. Plano All weather.

Now I just need to wait for the side wheel. I was able to shoot 40 yards today and the accuracy is right on. It is more accurate than my custom disco when the wind does not blow the pellet.

And if you can notice. I made the spacers not the palm rest longer. I need the extra height when shooting from seating position.

Excellent work on the knob! Send me one for my Mueller!!!

Rdsail · « **Reply #25 on:** June 04, 2014, 07:48:36 PM »

I wish it would work. I would send you a pdf. But there are too many variables that apply

azoutdoorsman · « **Reply #26 on:** June 04, 2014, 09:00:12 PM »

Quote from: Rdsail on June 04, 2014, 07:48:36 PM

I wish it would work. I would send you a pdf. But there are too many variables that apply

What about the knob itself?

1.4" scope centerline over bore
18.1gr JSB
880 FPS MV
25 yard zero
My scope is identical to yours Mueller Tactical 8-32x44 side focus

Rdsail · « **Reply #27 on:** June 05, 2014, 07:50:22 AM »

it is not that easy. When i did mine I had had to fine tune it some before not all the click where right on. Also, you need to get the knob and have actual diameter for the knob

Rdsail · « **Reply #28 on:** June 12, 2014, 07:49:55 AM »

Picture of my scope wheel after it was printed. I should be getting in a few days

Rdsail · « **Reply #29 on:** June 12, 2014, 08:05:16 PM »

New Knee/hamster finished and installed. It made of 3 pieces of oak. The two outer ones are .5 in and the middle one .25. I added 4 ½ x ⅛ steel rods in the inside for weight.

This is a lot more comfortable than the AA one. and it balances the gun better.

I think I did a fairly good job matching the wood stain.

sixshootertexan · « **Reply #30 on:** June 12, 2014, 09:41:43 PM »

Looking good Dan.

Rdsail · « **Reply #31 on:** June 16, 2014, 06:39:49 PM »

I just go the Sidewheel from the 3D printer. It looks great and it is very light. I'm putting a couple of coats of poly on it to make it smoother for the tape. I added 4 set screws to keep it centered.

here are the pictures

larspawn · « **Reply #32 on:** June 16, 2014, 07:28:53 PM »

How much will the printed wheel weigh versus aluminum?

Rdsail · « **Reply #33 on:** June 16, 2014, 07:32:41 PM »

It end up being $84 shipped. but if I were to do it again. I would just doit in white and spray painted black. The the cost would go down about $10.

Rdsail · « **Reply #34 on:** June 16, 2014, 07:36:14 PM »

here is the link. you want to http://www.sculpteo.com/en/print/sidewheel3/kfi3dMwu?uuid=WmwWKVCUKBekmhOAY68Xac

Rdsail · « **Reply #35 on:** June 20, 2014, 06:17:35 PM »

I made the side wheel tape. It sure takes a long time to make all the yardage markings.

smartshooter · « **Reply #36 on:** June 21, 2014, 02:54:55 PM »

I love that little gun and am really wanting to get my hands on one. what pellets have you found it likes the most? where you on a waiting list for a long time before yours came in i've heard the're getting hard to come by? I would love to see some groups out to 40-55 yards!!!

Thanks for sharing!

Rdsail · « **Reply #37 on:** June 21, 2014, 03:01:51 PM »

The only groups I have shot at that distance is when I was rechecking my click at 55 its was an easy .25in with a 8-10mph cross wind. I'm very impressed with how this gun shots. It is just easy. my range only allows me to shot to 40 yards. I'm shooting JSB 8.4s exclusively. I tried them first and it is the only pellet I have tested. They grouped so well that I did not bother to test any other pellet.

I'm also practicing for FT so I have hardly shot from a bench on the longer ranges.

smartshooter · « **Reply #38 on:** June 21, 2014, 05:15:11 PM »

nice shooting! thanks for getting back to me so quick it looks like precision airguns has them in stock so the wait isn't too crazy. the other videos i've seen online show that the gun really likes those jsb 8.4's as well.

Good luck with the FT Practice and soon competitions.!

michaelthomas · « **Reply #39 on:** June 21, 2014, 06:47:22 PM »

Nice job on the wheel and tape.

Mike

Thank you to our advertisers!

AA S400 MPR FT Came In!!!!

Author Topic: AA S400 MPR FT Came In!!!! (Read 37223 times))