WEBLEY PATRIOT

[Mpac]

I just backed out the 2nd screw 1 full turn out on my trigger and it breaks good factory set was to hard and hurt my finger.Haven't shot a Patriot so I wouldn't know the difference ,my 135 isn't bad at all when shot.The 155 showed converted over to gas ram was a 130mm stroke.

[SwampDonkey]

Thanks fang and Mpac...so basically what I'm getting is that both preform about the same but the patriot is $100 more worth of pretty.  Is that about right?  heck I might just go pcp this time around...oh well...I have plenty of time

[WHITEFANG]

Yes I saw that to. I did not mess with the trigger settings on it. I have sweet triggers on all the Hatsans. I thought that article used the same ram for the 125 135 as well. But looking at the drawing Yu can see some counter sinking work might explain the 130mm. 

[aom22]

Here is 1 of my 135's. Yes that is a 12" barrel with the RWS 350 pro comapc muzzle brake on it.
The brake has been moderated.

WHITEFANG, do you think a Diana 350 Pro Comp muzzle brake would fit a Webley/Hatsan Patriot?
Or, do you think a Hatsan 125 Sniper moderator could be fitted to a Webley/Hatsan Patriot?
It would be extremely interesting to know whether an H135 XRD moderator could be fitted to a WH Patriot.
If only the H135 XRD were currently available in America.

It is a travesty that spare parts for Hatsan airguns are not available in the USA.
And, to a certain extent this shortcoming limits the ability of tuners and customizers to ply their trade or experiment
to bring the best out of Hatsan airguns.

[SwampDonkey]

well Gee thanks Mpac...had to go throwing the 155 torpedo into the mix lol....very nice looking rifle....well what say yall about the 155?

[WHITEFANG]

Here is 1 of my 135's. Yes that is a 12" barrel with the RWS 350 pro comapc muzzle brake on it.
The brake has been moderated.

WHITEFANG, do you think a Diana 350 Pro Comp muzzle brake would fit a Webley/Hatsan Patriot?
Or, do you think a Hatsan 125 Sniper moderator could be fitted to a Webley/Hatsan Patriot?
It would be extremely interesting to know whether an H135 XRD moderator could be fitted to a WH Patriot.
If only the H135 XRD were currently available in America.

It is a travesty that spare parts for Hatsan airguns are not available in the USA.
And, to a certain extent this shortcoming limits the ability of tuners and customizers to ply their trade or experiment
to bring the best out of Hatsan airguns.

Yes it will fit. As for chopping a barrel contact FLYING DRAGON and he can do this for you. Raine air as well. Many out there. Hatsan parts for the 125 can be bought from Umerex usa. They are mostley the same as the WFH and THE WFT. Barrels will interchange for the most from the 125 to the 135.
Sniper could be made to fit as well but would take much effort. I would construct one of my own before making the sniper fit.

[aom22]

As for chopping a barrel contact FLYING DRAGON and he can do this for you.
Raine air as well.
Many out there.

Any airgunsmith choking Hatsan barrels?

WHITEFANG ... thanks for your response and information.

[WHITEFANG]

Any time. Got some materal laid out for some new brakes.

[z28rod]

mike melick can cut and choke barrels like the fang stated before, just call him.

[aom22]

As for chopping a barrel contact FLYING DRAGON and he can do this for you.
Raine air as well.
Many out there.

mike melick can cut and choke barrels like the fang stated before, just call him.

Sorry, but I didn't quite catch the choke barrels part from what WHITEFANG said.
Either way, I guess an email to Mike Melick might be in-order.