Nemesis X Rides Along . . .

[Back_Roads]

 Maybe try a new oring on Nemi 1
I tried Daisy hollow points, with no glory and 2" groups at 10m, went back to the 17.6 gr Norma and 5 clearing shots got it back to one hole 

[HunterWhite]

Yes, I did see co2 mentioned,  I know that the Sig MPX and MCX were co2 using 88/90 gram cartridges.  I was thinking that I had seen a Webly similar to the Nemesis X in co2.
I use air, but many people don't have that, so co2 and nitrogen are options.


These are interesting, I kind of wish that I had picked up one of these while they were on sale.


Hunter

[Xraycer]

Yes, I did see co2 mentioned,  I know that the Sig MPX and MCX were co2 using 88/90 gram cartridges.  I was thinking that I had seen a Webly similar to the Nemesis X in co2.
I use air, but many people don't have that, so co2 and nitrogen are options.


These are interesting, I kind of wish that I had picked up one of these while they were on sale.


Hunter

I've recently got one of those d/c compressors and so far I absolutely love it! At well under $200, it's very affordable now for just about anyone to get into pcp.

[Xraycer]

Maybe try a new oring on Nemi 1
I tried Daisy hollow points, with no glory and 2" groups at 10m, went back to the 17.6 gr Norma and 5 clearing shots got it back to one hole 

It's been 5 days and the pressure gauge needle hasn't moved all. It appears the plumbing teflon is working. The leak issue isn't a deal breaker for me, since the bottle is removable.
In regards to the Daisy hollow points, the ones that I'm referring to are the older(discontinued?) ones made in Spain, in the tall tin.

[Back_Roads]

Maybe try a new oring on Nemi 1
I tried Daisy hollow points, with no glory and 2" groups at 10m, went back to the 17.6 gr Norma and 5 clearing shots got it back to one hole 

It's been 5 days and the pressure gauge needle hasn't moved all. It appears the plumbing teflon is working. The leak issue isn't a deal breaker for me, since the bottle is removable.
In regards to the Daisy hollow points, the ones that I'm referring to are the older(discontinued?) ones made in Spain, in the tall tin.

I have the tall tin a rounded HP more like a H&N Hunter but rounder nose I have some .22 H&N  HP that are like the old winnie  .177HP ... Hmmm

[martrage]

 James , I am using the Daisy HP's in my Kral NP-03 "rat gun". They are flying at ~ 700fps & up to 25yrds are minute of vermin head. The Mrod FT handled
 them at around 800 but threw flyers more than I liked. The Crosman Drifter likes them also.

[dan_house]

Mine arrived yesterday, delayed a day due to weather between myself and PA....

some how missed the foregrip/bipod and the airhose connector being included. soooo Bonus!!

Gun handles well, like the size, the pistol is more vertical so that fits me better, its light weight. now gotta find some optics for it, a muzzle device, some chrony numbers then send some down range

has anyone noticed a fav pellet it likes?

[Back_Roads]

 18 grain jsb or the like, 21 grain H& N slugs and I get decent results with Norma 17.5 gr domed also. about all I tried so far all were good.

[Xraycer]

...has anyone noticed a fav pellet it likes?

Page 2 has several that I had tested.

From my pellet stash, the ones that did the best are the old Daisy hollow points that were made in Spain. I only have a few tins of these left, so I'm going to conserve them for pesting. Mainly, I fed the NX Hades or JSB 15.89g.
The NX has a choked barrel. It hated my JSB Knockout slugs and it hated CPHP!

[dan_house]

thanx for the pellet info

ok, that'll be this week end's task

[dan_house]

quick update.....
negatives to report.... the single shot tray can move around if you put any pressure  on it(l lean that area of the gun with the side of my finger), and I have managed to drop a couple of pels between the bolt and the "body", necessitating shaking the gun muzzle down to coerce them to leave. After installing the muzzle device you can hear some hammer bounce. not much LoP adjustment, but it aint bad for my preference.

Positives? 45 shots on the reg with a less than 3K fill,  can pop 2 inch targets at 42 - 45 yards with just support from the window frame. Attributing much of that to how light the gun is. trigger is wearing in better, but it wasnt bad OOB.

Like Dinh showed in one of his pics, I put an AR foregrip thingie on mine. Moved it as close to the trigger guard as I could. really helps holding it off hand. Not of the fan of the supplied vert grip/bipod, so slapped on a cheapie folding bipod right at the muzzle end of the lower rail. added weight that far out seems to help off-hand too. to tame the bark I found a Crosman threaded monocore in the parts box that screwed right on. had some tube that the core fit perfectly in, and 3d printed a piece to slide the tube over and seal it at the rear of that assembly. so the gun is only the length of the core longer, but its wayyyy quieter. Also added a bit of stair tread tape on the butt plate. helps hold it in place when shouldered. Have a JDK 10-40 SFP with the NATO "range-finder" reticle (dont ask, chinese scope distributed-at the time- thru some eastern European country, that I got at the gun show cheap years ago....) turned down to 10x so itll focus at 10 yards, with two sunshades.

I bought his gun as a toy, something grab to repel the marauding hordes of soda cans or dispatch that one gopher that always digs under the outside wall of the shop. Really had/have no plans to mod it..... but..... would really like to do something about the grey forearm (spray paint, hydro dip, rit dye job), minor addition to the pistol grip (3d printed, epoxy putty for a thumb shelf) and the hammer bounce(likely nothing or maybe an attempt at the 3 oring setup from the Marauder days).