Hatsan Jet I/II Discussion

[Houdini]

The easy fix is to get one of these to attach to the Hatsan fitting and then just attach it to your fill whip:



So I just need to make sure I understand. If I get that adapter, I would screw in the male part of the Hatsan QD into the female part of the adapter and then use the Adapter nipple to the Airforce QD female?

[Rat Sniper (AKA: PaulT58)]

So I just need to make sure I understand. If I get that adapter, I would screw in the male part of the Hatsan QD into the female part of the adapter and then use the Adapter nipple to the Airforce QD female?

Exactly! 

[Houdini]

So I just need to make sure I understand. If I get that adapter, I would screw in the male part of the Hatsan QD into the female part of the adapter and then use the Adapter nipple to the Airforce QD female?

Exactly!

Great, I appreciate the help. I want the 1/8 BSPP right, not the 1/8 NPT?

Hopefully the adapter fits my airforce QD! I will let you know what happens.

Thanks agan

[Houdini]

So I just need to make sure I understand. If I get that adapter, I would screw in the male part of the Hatsan QD into the female part of the adapter and then use the Adapter nipple to the Airforce QD female?

Exactly!

Great, I appreciate the help. I want the 1/8 BSPP right, not the 1/8 NPT?

Hopefully the adapter fits my airforce QD! I will let you know what happens.

Thanks agan

Thanks again for the help. The adapter worked out great!

[Rob M]

I chronied my jet, oddly it was shooting real slow , mid 500s with premiers.. I added a hammer spring spacer on the guide , now in the 630s.. Still a bit slower than I anticipated from the stock gun.

[scopecreep...]

I finalized the sling setup this afternoon with a 7/32" hole drilled in the stock and a 550 cord loop.

A layer of aluminum duct tape on the upper and side bearing surfaces inside the rear portion of the sliding stock took out the slop.

[Rat Sniper (AKA: PaulT58)]

I finalized the sling setup this afternoon with a 7/32" hole drilled in the stock and a 550 cord loop.

A layer of aluminum duct tape on the upper and side bearing surfaces inside the rear portion of the sliding stock took out the slop.

That sling set-up looks really good!  I used a piece of electrical tape to get rid of the slop in the stock, it did the trick!

[Rob M]

25 caliber for 233

https://www.ebay.com/itm/144846444162?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=d1VlgcuaRxK&sssrc=2047675&ssuid=QhK1jeFHQLe&widget_ver=artemis&media=EMAIL

[hfenn]

My Jet2 .177 has a Crosman red dot and homemade LDC attached with DonnyFL 1/2-20 adaptor. Pictures of gun and targets. It was windy today. It favors the lighter CPL 7.9 over the Benji 10.8 or JSB 10.4. I have some lighter Gamo and Polymag's to try.

[scopecreep...]

Thirsty little guy, I got tired of pumping over 3000 psi. It takes longer to fill the filters on my compressor than the gun. Rather than cycle the compressor for short periods I caved and bought a small bottle. Had a very relaxing afternoon. Factor this into your budget if you're not already equipped.

[Houdini]

So I just need to make sure I understand. If I get that adapter, I would screw in the male part of the Hatsan QD into the female part of the adapter and then use the Adapter nipple to the Airforce QD female?

Exactly!

Great, I appreciate the help. I want the 1/8 BSPP right, not the 1/8 NPT?

Hopefully the adapter fits my airforce QD! I will let you know what happens.

Thanks agan

Thanks again for the help. The adapter worked out great!

If anyone is interested in a decently priced case, I found this on Amazon. Good reviews. Decent Price. What I like about it is that it is well under 4 inches tall, while most cases of this size are 6"+. I said "decent price" It was still $85.00 but that was cheap compared to other options I found and this is really well made. IP67 Waterproof & Dust Proof: Rubber gasket lines the rim of the case, when latched closed creates a waterproof seal, pressure valve etc.... all while being light weight compared to the others.

Search: EYLAR Large 22 inch Protective, Camera, Tools, Equipment Laptop Hard Case Waterproof w/ 3 Layers Foam (Black)

Enjoy!

[Rat Sniper (AKA: PaulT58)]

That's a great looking case Harry!  Nice job on the cut-outs also, looks like it was made for the Jet!  It would have been nice if Hatsan had actually supplied a case, like the early pictures showed, but that's a great alternative!

[Back_Roads]

 Being able to pop it apart and back together quick is a one up on the Notos for sure 

[Rat Sniper (AKA: PaulT58)]

Being able to pop it apart and back together quick is a one up on the Notos for sure 

I agree, another plus is the ability to remove the moderator to make it even more sompact for travel.  Once Hatsan releases the spare air cylinders, you'll also have the option of a second, hot swappable 40cc air cylinder.  Which will be nice since I'm only getting about 12 shots per fill! 

[avator]

Nice looking set up y'all got there.
Pual.. get you one of those EaZy fill adapters and make that little bottle last even longer. No bleeding the line between fills.

[Rat Sniper (AKA: PaulT58)]

Nice looking set up y'all got there.
Pual.. get you one of those EaZy fill adapters and make that little bottle last even longer. No bleeding the line between fills.

I need to invest in one, but they are pretty pricey!  I have a 90ci Guppy Tank, but for some odd reason, when I try to fill the Jet, the air bleeds ot after I shut the valve and bleed the line.  It fills fine from the compressor, so I'm not sure why it does that when filling from the tank. 

[avator]

Nice looking set up y'all got there.
Pual.. get you one of those EaZy fill adapters and make that little bottle last even longer. No bleeding the line between fills.

I need to invest in one, but they are pretty pricey!  I have a 90ci Guppy Tank, but for some odd reason, when I try to fill the Jet, the air bleeds ot after I shut the valve and bleed the line.  It fills fine from the compressor, so I'm not sure why it does that when filling from the tank.

Look in the bargain gate.. there was a knock off for about half the price.

[avator]

Here it is....

https://www.aliexpress.us/item/3256804492064956.html?srcSns=sns_Copy&spreadType=socialShare&bizType=ProductDetail&social_params=20748201228&aff_fcid=521308ff61ca483e8c922592af469bab-1674822981300-05303-_mO7rEBo&tt=MG&aff_fsk=_mO7rEBo&aff_platform=default&sk=_mO7rEBo&aff_trace_key=521308ff61ca483e8c922592af469bab-1674822981300-05303-_mO7rEBo&shareId=20748201228&businessType=ProductDetail&platform=AE&terminal_id=df78c0aee6c24cbca6c4fdeb80bdb649&afSmartRedirect=y&gatewayAdapt=glo2usa&_randl_shipto=US

[Rat Sniper (AKA: PaulT58)]

I wish I could just find one of these in the US!  I already have a fitting for the end of the hose, but adding a check valve would do the trick.  Seems shipping from the UK has gone nuts lately, everywhere I find these are in the UK and they want $60+ to ship a $20 item!

https://www.bestfittings.co.uk/shop/airgun-charging-equipment/compressors/best-fittings-one-way-valve-quick-coupler-compressor-connector-male-female/

This would also work for filling my 90ci Guppy tank from a small compressor.

[avator]

Yep, just gotta figure how to bleed off the fitting. The EaZy fill spits out the pressure at the fitting only upon release of the lever. very little wasted air.
I use it on my 30min SCBA tank and it's awesome. The only issue is using it on some of my 2k guns that don't have pressure gauges like the FD-PCP and a couple of my HPA lego builds. I suppose I could rig a gauge between the adapter and the gun but I haven't yet.