What airgun related did you do today?

[45Bravo]

I was setting the internal regulator on one of my 500 cc air force tanks to get it shooting at sub 10 ftlbs for backyard plinking and indoor pesting.

Fill it shoot it, drain it, adjust it, repeat.   

It emptied my pony fill bottle more than once below the reg pressure, so had to top it off while I was adjusting the regulator.

I would hook it to my omega super charger and it would be back at 4500 psi by the time I was ready to fill my 500 tank again.

I am so glad I got a quality compressor.

It sits in the corner and makes about as much noise as a dishwasher while filling. 

Sounds like a tv ad, but connect it, push the button and forget it. 

Ian

[Privateer]

Sent a couple PM's to people in Murfreesboro, TN
I have to go baby sit a crew there for a few days next week so figured I'd try to hook up with them.
 

[Rabbit\Squirrel Killer]

I resealed a Crosman 44 and shot it a bit.

[Insanity]

I 3D printed a barrel band for my Gauntlet.  I found it on Thingiverse and thought I'd give it a try.  The ID was a bit too tight, but a little sanding opened it up enough to give a good snug fit over the air tube and shroud.  This thing really stiffened the barrel!  I referred the scope and was getting nice tight groups using H&N Sniper Mediums!

A 3d printer really opens up new opportunities doesn't it?

[Rabbit\Squirrel Killer]

I resealed a Crosman 44 and shot it a bit.

Here it is.

[45Bravo]

I need to see about 3D printing a suppressor that is flat on the bottom.

To fill my AA t200 I have to take the reservoir off, and a standard suppressor (1 inch of or bigger) won’t work.

So either 7/8 inch max diameter, or flat on bottom for about 2 inches. 

[Hoosier Daddy]

Ian... look into a TKO.

[Rat Sniper (AKA: PaulT58)]

I 3D printed a barrel band for my Gauntlet.  I found it on Thingiverse and thought I'd give it a try.  The ID was a bit too tight, but a little sanding opened it up enough to give a good snug fit over the air tube and shroud.  This thing really stiffened the barrel!  I referred the scope and was getting nice tight groups using H&N Sniper Mediums!

A 3d printer really opens up new opportunities doesn't it?

It sure does!  Really enjoying this thing!  LOL!

[Blowpipe Sam]

I boxed up the Air Hawk elite II (what mouthful) for shipment back to Umarex.  Then I took the dogs for a walk down to the river.  Toted the 2100 in case we saw a cotton mouth.  Still feeling cruddy from the flu.

[anti-squirrel]

I fondled groped massaged caressed hefted my Leshiy and found it worthy.

Then I looked at some of the my unused scopes and rings, as well as putting all my .22 pellets together.  Tomorrow might be a busy day

[45Bravo]

I have used many of theirs over the years.

And they do sell one for the s200/t200.

But A: want something different, LOOKING and unique.
And B: just wasn’t ready to spend the money on the TKO.

[francois.du.nord]

I degassed my Stormrider and removed the manometers to silicone grease threads and tighten, all the better to eliminate leaks.

[Insanity]

I need to see about 3D printing a suppressor that is flat on the bottom.

To fill my AA t200 I have to take the reservoir off, and a standard suppressor (1 inch of or bigger) won’t work.

So either 7/8 inch max diameter, or flat on bottom for about 2 inches.

I have found a square one on thingyverse.

[avator]

Going to run the 4 wheelers over to the site of the GTA Fun Shoot East coming up in May to take measurements and pics today..... rain permitting.

[maraudinglizard]

Emptied out the pellet trap, it was getting a little heavy to carry around. Needed more lead for the big bore guns.

[Rabbit\Squirrel Killer]

Going to run the 4 wheelers over to the site of the GTA Fun Shoot East coming up in May to take measurements and pics today..... rain permitting.

You need a waterproof camera so you don't need to worry about the rain. 

[triggerfest]

Scanning the internet for a new buy.....

[Hoosier Daddy]

Bent some sheet stainless to make two shelves for the pellet trap for the indoor game hunting.
 They are just taped in place for now to figure out the spacing. Then I will pull off the cover coating and screw them to the wood sides.

[avator]

Psshhh, you ain't got a hair on your butt if you don't shoot paintballs in the living room...

[bReTt]

Psshhh, you ain't got a hair on your butt if you don't shoot paintballs in the living room...

If you dare wear short shorts, Nair wears short shorts.   Ha ha ha ha ha!  You are funny Bill.  Now Dinh will pop in with a picture of a man wearing short shorts!  😱😱😱