Maximus with Marauder Trigger Gen 1 or Gen 2?

[JohnnyD143]

Which generation of trigger will work with the airgunlabs spacer? Apparently gen 1 and 2 trigger groups differ from each other... Any help is appreciated thanks

[bgmcgee]

Gen 1 would be the one you want.

[JohnnyD143]

Gen 1 would be the one you want.

Any idea where I can find one?

[GLPalinkas]

Gen 1 would be the one you want.

Any idea where I can find one?

Call Crosman. I just bought one for my Discovery. (800) 724-7486

Marauder Trigger group Gen I p/n 1763A105

I think I paid around $40 but I bought a lot of stuff so don't quote me. Shipping is a set $6

[Dairyboy]

Gen1 be prepared to cut your stock up to make it fit already put one on mine

[JohnnyD143]

Gen1 be prepared to cut your stock up to make it fit already put one on mine

Is it easy or is it for more advanced tinkerers like yourself dairyboy.... also thank you for the part number GLPalinkas!

[daveb50]

I put one in a Disco, just had to sand the sides of the opening till it dropped in. Removed maybe 1/16" on each side with a dremel and sanding drum attachment. I also used the Benjamin Trail Trigger Guard # B18-00-11A less than $2.

[JohnnyD143]

I put one in a Disco, just had to sand the sides of the opening till it dropped in. Removed maybe 1/16" on each side with a dremel and sanding drum attachment. I also used the Benjamin Trail Trigger Guard # B18-00-11A less than $2.

Do you have a picture of what it looks like with that trigger guard?
Thank you

[daveb50]

Here is a picture of it with the guard installed backwards. I didn't take a pic after turning it around, and no longer own it.

[Monkeydad1969]

Here is a picture of it with the guard installed backwards. I didn't take a pic after turning it around, and no longer own it.

Nice to see that it fit.

Joe

[JohnnyD143]

Here is a picture of it with the guard installed backwards. I didn't take a pic after turning it around, and no longer own it.

Nice to see that it fit.

Joe

It might even look factory with a Boyd's stock... I've been contemplating a Maximus Hunter, lane reg, a form of a tko with 1/2 UNF,  ssg from somewhere, and a Boyd's stock probably the varmint thumbhole in pepper laminate

[Dairyboy]

The stock was not hard to cut with a dremel. The parts where you need to cut are very thin.

[Monkeydad1969]

Take a look at my post on the Euro Maximus.  It only has 2 retaining screws holding the valve.  So I think once the parts are available I will order several barrels --- a couple without the threads and few more with--- and I will get the hammer springs.  They are short and stout.  Perfect for say a Cothran build.  I will use Disco tubes or Cothran tubes for my builds.
Joe

[JohnnyD143]

Take a look at my post on the Euro Maximus.  It only has 2 retaining screws holding the valve.  So I think once the parts are available I will order several barrels --- a couple without the threads and few more with--- and I will get the hammer springs.  They are short and stout.  Perfect for say a Cothran build.  I will use Disco tubes or Cothran tubes for my builds.
Joe

I wonder if it would be a better choice to buy a disco, and then the barrel off a euro with the threaded end cap. With the regulator I am only looking for 20 shots at 32 fpe, so I might need to fill over 2k but I am not sure.
John

[Monkeydad1969]

That's the way I'd go.