.25 and .30 NOE Pellet Molds.

[KnifeMaker]

Wayne, looks great! My finger is hovering over the buy button, but without at least a 40 yard target, no way for me. Simply cannot afford the gamble.

Your 20 yard target looks very good to me.

Knife

[KnifeMaker]

Thanks for the contact Wayne. I can finally get the cramps out of my finger just as soon as I can hit that buy button!

Knife

[Wayne52]

Each time I've been getting out recently I've been doing 5 shot groups to make sure I'm hitting decent.  This group is decent enough I didn't tweek the scope and it's still hitting about the same as last time. I honestly think that on my DAR25 the groups have tightened up considerably right at about 900fps because when I was doing more in the low 800's they were never this tight.

[KnifeMaker]

Wayne, what is the twist rate on this AG?


Nice Group!


Knife

[Wayne52]

Michael I'm not really sure what the twist rate is, the next time I take the barrel off I'll get a ball park figure using a tight patch with a marked rod, it is unchoked though.  They're really a neat new gun on the market but they have to be tinkered with to get them working right.  Very cheap to buy right now too, Sportsmans Guide has a super cheap sale on them right now and using the free shipping code you can get them delivered for about $250.  I think the 177's are cheaper yet.  Before I tuned it to shoot slugs it was getting 20 shots @ 52fpe but turning it up for 60fpe knocked it down to 6 regulated shots with another 4 good usable shots.  I can't use the slugs (BBT's) in it because they fit way too tight but do shoot very good out of it when I did check.
They're a mono block design that also has a delrin sleeve in them for the hammer, my .177 is a lot of fun too and shoots all the heavy pellets really nice.

here's the last chrony test for the .25 using the 34.5 grain cast pellets

1.   908.3 fps   62.59 fpe          6.   896.3 fps   61.55 fpe
2.   911.6 fps   63.67 fpe          7.   884.6 fps   59.92 fpe
3.   887.0 fps   60.28 fpe          8.   867.8 fps   57.70 fpe
4.   904.0 fps   62.61 fpe          9.   869.2 fps   57.89 fpe
5.   905.0 fps   62.75 fpe          10. 872.0 fps   58.26 fpe

here is a chrony test of the .177 using the H&N Sniper Magnums

[KnifeMaker]

I need to source a delrin or nylon sleeve for the RS.  Daystate uses them not for both shot consistency and to prevent damage to the hammer spring tunnel. .

[Killfire]

I need to source a delrin or nylon sleeve for the RS.  Daystate uses them not for both shot consistency and to prevent damage to the hammer spring tunnel. .

Knife if you have a lathe, I can send you some nylon rod as long as I have the right od.

[KnifeMaker]

I need to source a delrin or nylon sleeve for the RS.  Daystate uses them not for both shot consistency and to prevent damage to the hammer spring tunnel. .

Knife if you have a lathe, I can send you some nylon rod as long as I have the right od.

Thank you for the offer Sir. But no lathe. Only a mill. And NO Room for even a small lathe in the shoop. Man it's full!!!

[Killfire]

I need to source a delrin or nylon sleeve for the RS.  Daystate uses them not for both shot consistency and to prevent damage to the hammer spring tunnel. .

Knife if you have a lathe, I can send you some nylon rod as long as I have the right od.

Thank you for the offer Sir. But no lathe. Only a mill. And NO Room for even a small lathe in the shoop. Man it's full!!!

C'mon there's ALWAYS room for another toy, I mean tool. Well if you give me a sketch of what you need with some dimensions I can try and whip something out to you.

[KnifeMaker]

lol, still trying to figure what way I want to go with this idea. I did find thin wall at McMastercarr.  Got so many things, (ideas with this Rainstorm I Get confused just thinking about it. LOL


Knife