GTA

All Springer/NP/PCP Air Gun Discussion General => European/Asian Air Gun Gates => Turkish AirGun Gate => Topic started by: Pete on February 15, 2012, 03:30:47 AM

Title: Seals
Post by: Pete on February 15, 2012, 03:30:47 AM

I needed a seal for my 55... Since no one other than
Hatsan make them...
I decided to make one or two...
I tryed a softer urethane "orange" than I usually
use... but way to soft so back to the harder urethane..

red stuffs hard enough to machine but the orange what a ?..

Title: Re: Seals
Post by: Mike 4888blues on February 15, 2012, 04:24:03 AM

Quote from: pete on February 15, 2012, 03:30:47 AM

I needed a seal for my 55... Since no one other than
Hatsan make them...
I decided to make one or two...
I tryed a softer urethane "orange" than I usually
use... but way to soft so back to the harder urethane..

red stuffs hard enough to machine but the orange what a ?..

Gees  pete they look pretty darn good .. just like the jm seals
 Pete  can you see my new post and ad some info, its about removing trigger and main spring on the hastan 95.
If you can cool if not some one will
 best regards Mike

Title: Re: Seals
Post by: Pete on February 15, 2012, 05:21:02 AM

The finish is ok...
but I need to play around with the
rake angles on the tools..see if
I can get a better finish..

Title: Re: Seals
Post by: Raizer on February 15, 2012, 02:06:08 PM

They look really good Pete!

Hey you wouldn't happen to know what size seal the strikers use would you?
I want to lube mine, but want to find a seal etc before I pull it apart lol

Title: Re: Seals
Post by: Pete on February 15, 2012, 04:49:20 PM

Quote from: Raizer on February 15, 2012, 02:06:08 PM

They look really good Pete!

Hey you wouldn't happen to know what size seal the strikers use would you?
I want to lube mine, but want to find a seal etc before I pull it apart lol

26.75 ID
To check..measure the tubes OD if its
31mm OD then it has a 26.75 bore..
Hatsan is the only one that
makes that size at the moment..

Title: Re: Seals
Post by: downalap on February 15, 2012, 06:10:47 PM

Pete,  are the stock seals on newer Hatsan rifles a good fit from the factory or are they likely to be "undersized"  like some of the old gamo guns were?

Title: Re: Seals
Post by: Pete on February 15, 2012, 07:15:59 PM

They don't seem to be to bad...
BUT I had a turkish Webley Patriot
the seal in that was like 1mm under size..(38thou)
It was so far undersize I think it just got the wrong
seal put in it..like a Mod 125 /135 seal
The seals are very hard urethane..I suspect
they use a urethane around 75D.where mine
are 95A...

Title: Re: Seals
Post by: Raizer on February 16, 2012, 01:13:49 AM

Quote from: pete on February 15, 2012, 04:49:20 PM

26.75 ID
To check..measure the tubes OD if its
31mm OD then it has a 26.75 bore..
Hatsan is the only one that
makes that size at the moment..

Just measured and yeah its 31mm OD, what would you want for a seal?

Title: Re: Seals
Post by: Mike 4888blues on February 17, 2012, 01:18:06 PM

Quote from: downalap on February 15, 2012, 06:10:47 PM

Pete,  are the stock seals on newer Hatsan rifles a good fit from the factory or are they likely to be "undersized"  like some of the old gamo guns were?

my stock 95 seal had a small metal flake inbeded in it  on the side, as you know I  used a new j m seal after modding the piston button.
 i saw on my piston at the area of the sear knock out thin metal that was bent over from not cleanly removed  i grounded  that off  and cleaned it during the tuning

Title: Re: Seals
Post by: Raizer on February 22, 2012, 09:38:01 PM

Mine arrived this morning, looks even better than the pics!