GTA
All Springer/NP/PCP Air Gun Discussion General => PCP/CO2/HPA Air Gun Gates "The Darkside" => Topic started by: moose on July 22, 2022, 09:13:31 PM
-
I am wanting to put a DonnyFl Tanto on my prod. I am just debating on which adapter I need to use. just want to figure out the easiest way to get the connector to the fill port without having to take the suppressor off everytime.
Ideally I would like to use the short adapter and the Tanto Cone Endcap.
If anyone has this setup, any info is appreciated ;D
-
I've had the extender w/ a Tanto, a OdB 110 and I've ended up with the Buck Rail. https://buck-rail.com/product/benjamin-marauder-pistol-suppressor/ It's as quiet as the others and way less weight.
I have a Tanto with the cone, on another gun, and just don't like the look.
-
I have a Neil Clague LDC on my Prod, it uses the full shroud, as ir screws to the shroud, all I hear is pfft. Have to Email and ask about his Marauder pistol LDC
Room to get a fill fitting on too,
http://petersoncorner.com/clague/default.htm (http://petersoncorner.com/clague/default.htm)
(https://www.gatewaytoairguns.org/GTA/MGalleryItem.php?id=7194)
-
I am wanting to put a DonnyFl Tanto on my prod. I am just debating on which adapter I need to use. just want to figure out the easiest way to get the connector to the fill port without having to take the suppressor off everytime.
Ideally I would like to use the short adapter and the Tanto Cone Endcap.
If anyone has this setup, any info is appreciated ;D
I have one on my 17xx (PROD tube and shroud) but I don’t use it ‘cuz it’s a low power AG, hence very quiet.
My adapter is the short one from Poland, not a DFL, but 1 of my Tantos is a cone while the other one is straight.
With the cone, you can remove the filler cap, but you would run the risk of scratching your Tanto with the quick connector.
Probably if the quick connector is a 90 degree (is there such piece?) it might work.
Hill Airguns sells 2 specific pickles for the PROD, btw.
1 is so small and less than 3”, IIRIC.
-
I use TKO and have used Rocker LDC.
No problem filling.
-
I do have a 90 degree fitting. it's still gonna be a tight fit !!
-
I tried it again today (straight fitting), and it's just too tight, although I taped it to avoid unwanted abrasion if I slipped.
Of you're like me who does not want even the slightest of scratches I'd just go for the Donny FL long adapter.
-
I tried it again today (straight fitting), and it's just too tight, although I taped it to avoid unwanted abrasion if I slipped.
Of you're like me who does not want even the slightest of scratches I'd just go for the Donny FL long adapter.
Thanks Rick67, appreciate the input. going with the longer adapter. less hassle all around !
-
With the Tanto:
(https://i.imgur.com/eKQyIvP.jpg?1)
Threaded 1" OD TKO:
(https://i.imgur.com/7ibzkwz.jpg?1)
In all honesty, the AG is most accurate with the TKO, not the quietest though, but it has the least POI change (due to its weight) and larger orifice.
Don Cothran Disco build ;D
(https://i.imgur.com/CdZFVoS.jpg?1)
-
I use the smaller paintball caps on several guns. Easier to get on & off and I can add a little bling, like red to match scope rings & wheel.
-
I kinda like the Hugget Atom and the mini 2.25" Hill moderator, but I'm already happy with the TKO's accuracy ;D
Actually, it was a PIF from Mobilehomer/Mr. Ken, but there was a bit of baffle damage, so I reached out to Mr. Mike of TKO.
He told me to send it to him, and he replaced it, then sent it to me w/o charging me a single cent.
I insisted on paying the gent, but he said, "NO, sir, its under warranty".
Wow ;D
-
I ordered the Tanto. But they sent me the Heavier FX, with no indication of caliber ?
-
I ordered the Tanto. But they sent me the Heavier FX, with no indication of caliber ?
Get ahold of them, theyll make it right. The tanto is a good option for the Prod. The Koi will even be quieter. I have one on a 50 fpe 25 and it's considerably quieter than the tanto on the same rifle, and the buck rail can't even keep up at that power.
-
I've got a Froggy239 ldc on my P-Rod. It's lightweight and pretty close to silent. I think it was around $35 on Ebay.
-
I have the Sumo LDC on the prod. Very backyard friendly.
-
I have a Tatsu and a Tanto. Both are fantastic but tbh, the Tanto is the winner. I also have a few of Rockers units on my lower power guns and they are amazing for the money.