GTA
All Springer/NP/PCP Air Gun Discussion General => Air Gun Gate => Topic started by: nced on June 21, 2020, 08:57:41 AM
-
Well....actually, I modified an existing 100 bull target created using CAD software a while back with the simple addition of an "aiming circle" inside the 3/8" diameter bulls and then deleted the bulls not needed for the 50 & 25 bull targets. They were created to fit the standard 8 1/2" x 11" letter format and I like to print them on 90# to 110# card stock. I have both the original .pdf format but and an exported .jpeg format so they could be added to the imjur a photo hosting site I use for posting..............
(https://i.imgur.com/IG96lKr.jpg)
(https://i.imgur.com/g34zl3z.jpg)
(https://i.imgur.com/eD2RFEn.jpg)
When shooting the targets before adding the "aiming circle" I found myself aiming at the "bull numbers" because they were smaller than the circles and I found that I could group tighter aiming at the numbers than trying to center a featureless circle.........
(https://i.imgur.com/Fx8RFOSl.jpg)
-
Well....actually, I modified an existing 100 bull target created using CAD software a while back with the simple addition of an "aiming circle" inside the 3/8" diameter bulls and then deleted the bulls not needed for the 50 & 25 bull targets. They were created to fit the standard 8 1/2" x 11" letter format and I like to print them on 90# to 110# card stock. I have both the original .pdf format but and an exported .jpeg format so they could be added to the imjur a photo hosting site I use for posting..............
(https://i.imgur.com/IG96lKr.jpg)
(https://i.imgur.com/g34zl3z.jpg)
(https://i.imgur.com/eD2RFEn.jpg)
When shooting the targets before adding the "aiming circle" I found myself aiming at the "bull numbers" because they were smaller than the circles and I found that I could group tighter aiming at the numbers than trying to center a featureless circle.........
(https://i.imgur.com/Fx8RFOSl.jpg)
Good job.
I like those, did you say you have them in pdf?
-
Well....actually, I modified an existing 100 bull target created using CAD software a while back with the simple addition of an "aiming circle" inside the 3/8" diameter bulls and then deleted the bulls not needed for the 50 & 25 bull targets. They were created to fit the standard 8 1/2" x 11" letter format and I like to print them on 90# to 110# card stock. I have both the original in .pdf format and exported in the .jpeg format for use with a photo hosting site..............
(https://i.imgur.com/IG96lKr.jpg)
(https://i.imgur.com/g34zl3z.jpg)
(https://i.imgur.com/eD2RFEn.jpg)
When shooting the targets before adding the "aiming circle" I found myself aiming at the "bull numbers" because they were smaller than the circles and I found that I could group tighter aiming at the numbers than trying to center a featureless circle.........
(https://i.imgur.com/Fx8RFOSl.jpg)
Yep........email me at ncedx27572@hotxmail.cxom (delete the "x"es)
-
Well....actually, I modified an existing 100 bull target created using CAD software a while back with the simple addition of an "aiming circle" inside the 3/8" diameter bulls and then deleted the bulls not needed for the 50 & 25 bull targets. They were created to fit the standard 8 1/2" x 11" letter format and I like to print them on 90# to 110# card stock. I have both the original in .pdf format and exported in the .jpeg format for use with a photo hosting site..............
(https://i.imgur.com/IG96lKr.jpg)
(https://i.imgur.com/g34zl3z.jpg)
(https://i.imgur.com/eD2RFEn.jpg)
When shooting the targets before adding the "aiming circle" I found myself aiming at the "bull numbers" because they were smaller than the circles and I found that I could group tighter aiming at the numbers than trying to center a featureless circle.........
(https://i.imgur.com/Fx8RFOSl.jpg)
Yep........email me at ncedx27572@hotxmail.cxom (delete the "x"es)
Thanks Ed