GTA
All Springer/NP/PCP Air Gun Discussion General => European/Asian Air Gun Gates => German AirGun Gate => Topic started by: eezapz2101 on April 09, 2016, 12:26:13 PM
-
http://youtu.be/znORQUx5MEU (http://youtu.be/znORQUx5MEU)
Hey guys so here's the video of the custom order vortek pg2 kit I got for my Diana 460 T06 but the coils are not consistent in diameter so I have no idea as to tell whether vortek sent me a stock Diana 48 kit witch comes with the .128 wire spring or they actually sent me my custom order of the .130 wire spring.
Anyway there it its I'm going to install it today and I'm going to upload the before and after once I finish
http://youtu.be/znORQUx5MEU (http://youtu.be/znORQUx5MEU)[/url]
-
Emiliano, looking forward to hearing how she shoots. You put a 48 kit in your 460? Is that to detune it a bit?
Scotty
-
I'm pretty sure the 48 and 460 kit are the same . I was wondering how it shoots also ,l was thinking of putting a vortek in my 460 also . The ARH kit for the 460 is a lot more than the vortek kit, not sure of the difference ,would be interested in knowing .
-
Emiliano, looking forward to hearing how she shoots. You put a 48 kit in your 460? Is that to detune it a bit?
Scotty
No, in fact I'm trying to up my rifles velocity,
http://youtu.be/znORQUx5MEU (http://youtu.be/znORQUx5MEU)[/url]
-
I'm pretty sure the 48 and 460 kit are the same . I was wondering how it shoots also ,l was thinking of putting a vortek in my 460 also . The ARH kit for the 460 is a lot more than the vortek kit, not sure of the difference ,would be interested in knowing .
http://youtu.be/znORQUx5MEU (http://youtu.be/znORQUx5MEU)[/url]
-
Why are you trying to up your magnum rifle velocity? And how fast are you wanting to achieve? I saw you had three thick washers/spacers there, how many did you install? And where did you install them?
-
Why are you trying to up your magnum rifle velocity? And how fast are you wanting to achieve? I saw you had three thick washers/spacers there, how many did you install? And where did you install them?
The reason i want more power it because the rifle was shooting a an average of 670fps with CHP 14.3g, And since I had an incident with my rifle were some parts broke so I figured I might as well debur, Polish and properly tune my rifle since I wanted more power a new spring was so very justified now.
I'm trying to get Arround 880 to 900 fps with the same pellet.
I did not install any washer yet, I want to try it first just with the spring it selfe and see what velocities I end up with after a couple of hundred pellets.
-
I would love to see the results whenever you have time to post them.
How much fps do you expect each washer to add should you need to add them to achieve your speeds? Or do you plan to add a washer and then chrony it, and so on?
Again i ask, have you considered how hold sensitive or hard it will be to shoot this monster in practice. With your numbers it will shoot 25fpe+ and that is gonna make for one "violent" shot cycle.
-
I would love to see the results whenever you have time to post them.
How much fps do you expect each washer to add should you need to add them to achieve your speeds? Or do you plan to add a washer and then chrony it, and so on?
Again i ask, have you considered how hold sensitive or hard it will be to shoot this monster in practice. With your numbers it will shoot 25fpe+ and that is gonna make for one "violent" shot cycle.
I'm sad to inform that it did not increase my fps
Check my new post with all the videos