1
PCP/CO2/HPA Air Gun Gates "The Darkside" / Re: Benjamin Fortitude Leak Question« Last post by Rick67 on Today at 04:47:08 PM »HF O-rings are no good at all and are just palliative. Told a member here a few years not to use them on his 13xx but he did anyway. Worked for a very short time 👍 I have a few boxes of them though for other purposes, and they just don’t last long; just breaks after a while as if they were snipped. 2
PCP/CO2/HPA Air Gun Gates "The Darkside" / Re: Benjamin Fortitude Leak Question« Last post by Rick67 on Today at 04:40:46 PM »Get 80D O-rings from Amazon in 113 and 016. Bought a bag of them, and they both share the same OD but different thickness.
These are the O-rings for the Discovery and the 17xx/Prod/Fortitude valves (outer), gauge block, and fill port assembly. 3
Air Gun Gate / Re: Airgun A, B, C's« Last post by fireslinger on Today at 04:36:48 PM »P is for pucher breaker (kral)
4
PCP/CO2/HPA Air Gun Gates "The Darkside" / Re: Benjamin Fortitude Leak Question« Last post by Rick67 on Today at 04:18:15 PM »HF O-rings are no good at all and are just palliative.
5
Georgia Fun Shooting Events / Re: Upper Middle Georgia Head Count« Last post by BmaS on Today at 04:00:34 PM »If any of you are still active on this board and in the hobby, I would like to meet up with you. I am moving to the Barnesville area in July 2024.
6
Air Gun Gate / Re: Airgun A, B, C's« Last post by bantam5s on Today at 03:43:23 PM »O is for Octane ( umarex)
7
Air Gun Gate / Re: So.....what did you shoot today?« Last post by splitbeing on Today at 03:18:41 PM »Here's a thought:
Make clothes for a zombie out of paper bag. Tape the ketchup packet to the underside. When shot, the bag will tear along with the packet, allowing the ketchup to run down the bag, which will also absorb some and so reveal a gross trail once the blood has dripped down slowly 57 bottle style. 8
PCP/CO2/HPA Air Gun Gates "The Darkside" / Re: Benjamin Fortitude Leak Question« Last post by Robert 5mm on Today at 03:13:51 PM »Usually when a slow leak occurs at high pressure and then eventually stops, it is because of one of two reasons: I think I understand and I am going to top of the line O-Rings this time on all locations. Last time I used some HF and some Captain O-Rings ( I did not have all the sizes - so I used some HF ) Thanks. I did try the balloon tests on the barrel - nope. 9
German AirGun Gate / Re: Difference between the 16J and 20J HW97K?« Last post by triggerfest on Today at 03:04:43 PM »The original poster was only asking if the difference between the two power levels is only the spring so that if he purchases the 16J version, he can later go full power if he choose to and that there was no permanent unalterable restrictions in the gun beyond the spring in order to achieve this. So the difference is 4J only obviously. Will you notice that ? Not really. The only reason why Krale sells the 16J version as well, while there are no power restrictions in Netherlands, people like to have a 16J version out of the box (= UK power limit restriction) to shoot FT/HFT competition on UK rules. In that case not more than 16J is allowed. But also no tune or spring exchange is needed. 10
PCP/CO2/HPA Air Gun Gates "The Darkside" / Re: Benjamin Fortitude Leak Question« Last post by nervoustrigger on Today at 02:56:53 PM »A leaking poppet (leak at the valve seat) does the reverse...leaks when the pressure is low, seals when pressure is high.
|