• Jefferson State Airrifles
  • Air Gun Web - Expert Airgun Reviews
  • Hajimoto Productions
  • Airgun Angie - Backyard Shooting
  • Nielsen Specialty Ammo
  • Dynamic Air Rifles
  • FX Airguns
  • DonnyFL - When silence is a priority
  • Airgun Archery Fun
  • Pyramyd Air
  • Saber Tactical
  • New England Airgun
  • Umarex Airguns
  • Contact us
  • Utah Airguns
  • SEKHMET Airgun Accessories
  • Freedom Gun Targets
  • Evanix Airguns at Airgun Pro Shop
Jefferson State Airrifles
Air Gun Web - Expert Airgun Reviews
Hajimoto Productions
Airgun Angie - Backyard Shooting
Nielsen Specialty Ammo
Dynamic Air Rifles
FX Airguns
DonnyFL - When silence is a priority
Airgun Archery Fun
Pyramyd Air
Saber Tactical
New England Airgun
Umarex Airguns
Contact us
Utah Airguns
SEKHMET Airgun Accessories
Freedom Gun Targets
Evanix Airguns at Airgun Pro Shop


Recent Posts

Pages: 1 ... 8 9 [10]
91
Air Gun Gate / Re: Improving front fiber optic post
« Last post by north country gal on Today at 10:56:05 AM »
The biggest issue with FO rods has been durability. They do break, easily, this the trend to protecting them more with layers of plastic and so on.
92
Good morning GTA! Up at 0550 CDST. Iím still deciding what to do today too John. We have a disturbance in the gulf that will bring rain,  lots of rain in the next few days. Yesterday was pleasant outside but a bad headache made shooting undesirable.

I hope your headache is better. I also hope some of that rain comes our way.
93
Speaking of shortagesÖ thereís a refrigerant shortage. They made us buy what we could yesterday. I basically have 2 jugs of everything we use and next week Iím on call. Theyíre talking about R22 may be finally done. And other types trickling in or not having any til July. Itís not like we use refrigerant everyday, so Iím not going to think about it til it becomes a problem. Besides, itíll be the officeís decision, ultimately.
94
Back Room / Re: The coffee lovers thread...
« Last post by Bicycleman on Today at 10:51:28 AM »
The only time I remember being served coffee in a Dixie Cup, the bottom of the cup dropped out!   :o >:( >:(
95
Thanks for that. Itís hard to tell about some vendors. I would have bought from the bintacllc site but it is very disorganized and confusing. He really needs a site update.

Dave
96
Crosman-Benjamin Air Gun Gate / Re: Crosman 140
« Last post by Van on Today at 10:46:52 AM »
  JG Airguns has the parts sold separately( $12.35 for the brass cap) but you have to send in the old brass cap as they exchange only. They rebuild the old cap. If yours is badly damaged I would let them know the condition before sending it in. It is the only place I know of as the brass cap is no longer made.  They sell the quad seals also if you could use just that.  If you want a rebuild kit that does not include the brass cap, Mac1 Airguns and Baker Airguns sell the complete rebuild kits for around $30.  I got mine from Mac1 which includes a O ringed type replacement for the pump cup which was hard as a rock on my gun.
97
PCP/CO2/HPA Air Gun Gates "The Darkside" / Re: Seriously Umarex?
« Last post by Nvreloader on Today at 10:44:17 AM »
Mike

What size is this "O" ring?
Are/Is the hole in the magazines covers the same size as the outside diameter of the bolts/probes "O" ring?

I had to open mine up a few thousands and deburr the plastic edges on both sides and add a very slight bevel etc,
as that was eating the "O" rings on my Gauntlets mags........... ;)

Made a world of difference on loading etc.

Tia,
Don
98
PCP/CO2/HPA Air Gun Gates "The Darkside" / Re: Seriously Umarex?
« Last post by tracker1955 on Today at 10:32:20 AM »
I don't think o-ring wear has as much to do with its location as it does alignment. Example: my Liberty has o-rings on the probe and after thousands of rounds they are still fine. I do keep them lubed which I'm sure helps, but I haven't noticed any air loss around them or change in FPS.
99
What about a Crosman 2240?  I always felt the stock grips felt small, but I have large hands/long fingers?

Plus many custom grips available for reasonable cost.

JMJinNC
100
Crosman-Benjamin Air Gun Gate / Re: Benjamin 392s
« Last post by avator on Today at 10:30:59 AM »
Found a suitable trigger return spring and got Betty Lou's trigger done. I did cut the anti decocking nub off of hers. Don't know why... I just did. Next time in I'll find some thin brass washers for the pivot pins. Maybe a trip to the old school hardware later.

avatar,

IMHO, the cutting of the anti de-cocking nub is a very, very big deal with me. I did it on all my airguns including my Airforce guns. If I could not de-cock, I would most likely not own the gun, that feature is that important to me as I want one in the chamber and cock and shoot when I want to in one semi quick motion.

As I'm walking around in the woods or waiting all I want to do is quietly and quickly cock the gun. I'm not about to walk around with a round in the chamber, spring tension on and relying on a mechanical safety --- not going to happen.

wll
I get it... just probably won't spend too much time in the woods with these 2 guns. They are more for Betty Lou and I to enjoy plinking games together like we do with many other pairs of pumper we have.
Pages: 1 ... 8 9 [10]