1
Welcome New Members / Re: Hello« Last post by ezman604 on Today at 11:12:59 PM »Welcome to GTA Forums Brad!!!
SAFE & Happy Shooting!!!! Dave 2
Welcome New Members / Re: So Cal airgun enthusiast« Last post by dk1677 on Today at 11:08:51 PM »Welcome to the GTA Jeff!
3
Welcome New Members / Re: So Cal airgun enthusiast« Last post by AThomas on Today at 11:08:00 PM »Welcome to the GTA!
4
Welcome New Members / Re: So Cal airgun enthusiast« Last post by ezman604 on Today at 11:06:59 PM »Welcome to GTA Forums Jeff!!!
SAFE & Happy Shooting!!!! Dave 5
Welcome New Members / Hello« Last post by FLBrad on Today at 10:53:40 PM »Hello all,
I've been a long time lurker on this sight since I stumbled across it when I was a teenager googling how to reseal my dads old Crosman 1400. I read a few posts here and before I even knew what happened I was ordering 1322s, flat top pistons, longer barrels and moderators. So thanks for getting me hooked on this hobby and I look forward to hopefully contributing to the corruption of the next generation of airgunner -Brad 6
PCP/CO2/HPA Air Gun Gates "The Darkside" / Re: FX Impact M3 Power Adjustments« Last post by PaulFWI on Today at 10:52:43 PM »I would not mess with the first reg. It may start to act up on you if disturbed. I would remove the bottle and bleed the remaining reg air before turning up the second reg. If you can still remove the bottle like with the MKII under pressure. You can always turn the second reg back down with pressure applied without risking much. Doing all of this should keep all working good. FWIW: I only have an MKII with one reg but have read enough posts that if I had an M3 I would be mostly familiar with it already except for the bottle valve. I am very familiar with tuning an Impact. I had no plans to adjust the 1st reg, which the manual says should not be done. (It does say to remove the bottle if you do.) The Mk3 manual does NOT say to remove the bottle for adjusting the 2nd reg - in fact, it says: "Make sure you have full pressure (200+bar) in the tank before starting this adjustment." 7
Boolit and Pellet Casting / Re: Newby on the block... well, to casting anyways.« Last post by triggertreat on Today at 10:48:10 PM »Quite the advancement from your humble beginnings. I can sense you want it, so have no doubt you will reach your goals.
8
Air Gun Gate / Re: Airgun A, B, C's« Last post by AirGunner on Today at 10:46:13 PM »Ironhide (Crosman break barrel)
9
Pellets all calibers / JSB 25.39gr 22 cal pellets« Last post by Dextrose on Today at 10:41:47 PM »Totally confused. What is the difference between the four 25.39gr pellet tins available from Pyramyd Air. 1) Exact Jumbo Monster 2) Redesigned Monster 3) Redesigned Exact Jumbo Monster Shallow Skirt & 4) Redesigned Exact Jumbo Monster Deep Skirt. All weigh 25.39gr, but have different names. Is any one of these a standout for a powerful PCP like the RAW HM1000x?
10
PCP/CO2/HPA Air Gun Gates "The Darkside" / Re: FX Impact M3 Power Adjustments« Last post by triggertreat on Today at 10:40:12 PM »I would not mess with the first reg. It may start to act up on you if disturbed. I would remove the bottle and bleed the remaining reg air before turning up the second reg. If you can still remove the bottle like with the MKII under pressure. You can always turn the second reg back down with pressure applied without risking much. Doing all of this should keep all working good. FWIW: I only have an MKII with one reg but have read enough posts that if I had an M3 I would be mostly familiar with it already except for the bottle valve. I am very familiar with tuning an Impact.
|