Tailstock Moynted Manual Tap Holder
Select Gate
READ GTA FORUM RULES BEFORE POSTING
GTA Forum Help Desk
GTA Announcement Gate
Dealer Area
GRIP
AirgunWeb Airgun Videos
Airgun Repository of Knowledge
Vendors and Vendor Videos
AirGun Expo 2021
Airgun Expo 2022
Contests and Giveaways!!!
Welcome New Members
In Memoriam
GTA Contributing Members
Shot Show Videos
Hajimoto Productions
Airgun Detectives
Air Gun Gate
BB Guns and Such
"Bob and Lloyds Workshop"
American/U.S. Air Gun Gates
European/Asian Air Gun Gates
PCP/CO2/HPA Air Gun Gates "The Darkside"
Air Archery
Vintage Air Gun Gate
Air Guns And Related Accessories Review Gates
Hunting Gate
Machine Shop Talk & AG Parts Machining
3D printing and files
Buyer's, Seller's & Trader's Comments
Bargain Gate
Back Room
Target Shooting Discussion Gate
Target Match Rules
Shooting Match Gates
Field Target Gates
The Long Range Club
100 Yard Match
Discussions By States
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email
?
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Home
About
Help
Old GTA
Gallery
Search
Stats
Login
Register
Advertise Here
GTA
»
All Springer/NP/PCP Air Gun Discussion General
»
Machine Shop Talk & AG Parts Machining
(Moderators:
Rocker1
,
GTA-Airgunner
) »
Tailstock Moynted Manual Tap Holder
« previous
next »
Print
Pages: [
1
]
Go Down
Share This!
Author
Topic: Tailstock Moynted Manual Tap Holder (Read 371 times))
Ronno6
GTA Senior Contributor
Posts: 5023
yes
Real Name: Ron
Tailstock Moynted Manual Tap Holder
«
on:
February 17, 2023, 01:36:35 PM »
I do some repetitive jobs that require small tapping...5-40 and 4.5mm.
I have been using a TS mounted chuck and allowing the tap to pull the TS in as it threads.
I need t wire up the reverse on my motor, but have not done so as yet.
So, tap extraction is a matter of hand turning the HS to back the tap out.
So..........I decided to purchase the sliding TS mounted tap holder, all of which come from India.
I received it and it LOOKS nice, nice wood case and all.
The 2MT mandrel was inserted, the knurled sleeve slid on, and the smaller of the 2 collets inserted into the sleeve and the SS snugged up.
That's where the good news stopped........
BOTH collets showed significant wobble, measured at up to .050" TIR...
So bad that the taps would not come close to the hole in the workpiece.......
The seller said that I "must have installed it wrong or not using it properly."
I sent photos.......we are working thru ebay on a return/refund..........
BTW...the 4th pic shows a Jacobe chuvk mounted in the sleeve ...that shows that all os goot except the supplied collets...
Logged
USA, Stone County, MS
You can lead a man to water, but you can't keep him from urinating in it.
KWK
Sharp Shooter
Posts: 590
yes
Real Name: Karl
Re: Tailstock Moynted Manual Tap Holder
«
Reply #1 on:
February 18, 2023, 02:19:51 AM »
Far out! Man.
Get the pun?
Through holes? Try gun taps. I think you'll like it.
Let's get that drum switch wired up.........
You know you won't have instant reversing, right?
Although instant reversing single phase motors are available. I have one for one of my south bends. Instead of a centrifugal switch it uses a relay to connect the start capacitor and windings. Instant reversing.
I think I could wire a refrigerator start relay to any small (1/2 hp) split phase motor eliminating the centrifugal switch and make it instant reversing. I might try that some time. Should work ok.
Logged
USA, PA, Camp Hill
OTmachine
Sharp Shooter
Posts: 767
it'll shine when it shines
Real Name: Keith
Re: Tailstock Moynted Manual Tap Holder
«
Reply #2 on:
February 18, 2023, 09:18:07 AM »
+1 on the Gun Taps
Logged
USA, Central WI
Ronno6
GTA Senior Contributor
Posts: 5023
yes
Real Name: Ron
Re: Tailstock Moynted Manual Tap Holder
«
Reply #3 on:
February 18, 2023, 09:34:52 AM »
Will gun taps help the gross misalignment?
virtually all holes I tap are blind.....
Logged
USA, Stone County, MS
You can lead a man to water, but you can't keep him from urinating in it.
KWK
Sharp Shooter
Posts: 590
yes
Real Name: Karl
Re: Tailstock Moynted Manual Tap Holder
«
Reply #4 on:
February 18, 2023, 11:41:42 AM »
No, they won't but they sure do thread through holes better.
Logged
USA, PA, Camp Hill
Print
Pages: [
1
]
Go Up
« previous
next »
GTA
»
All Springer/NP/PCP Air Gun Discussion General
»
Machine Shop Talk & AG Parts Machining
(Moderators:
Rocker1
,
GTA-Airgunner
) »
Tailstock Moynted Manual Tap Holder