Thank you to our advertisers!







Author Topic: How much jump before pellet hits the grooves?  (Read 2141 times))

Offline subscriber

  • GTA Senior Contributor
  • ******
  • Posts: 4709
  • yes
Re: How much jump before pellet hits the grooves?
« Reply #100 on: November 21, 2021, 04:30:00 PM »
So, Duy; did your groups shrink after cutting the shorter leade?


And for general speculation:  I wonder if smaller caliber slug guns are more sensitive to free-bore, because they have more projectile circumference in bore contact (friction), compared to the area that air pressure acts on to generate engraving force (and accelerate the projectile moving); because: 

Circumference is PI x D;
while area is PI x D X D / 4

As such, larger projectiles have engraving forces that increase with the diameter, but available air pressure forces that increase by the square of the diameter.  The inverse means that small calibers slugs with significant weight (flank length) may bog down more during land engraving. 

This obviously also depends on the how close the bearing diameter is to barrel groove diameter.  Dubber and his buddies have been shooting .22 cal slugs that are under groove diameter for a long time to good effect.  Members on this forum have recently noticed that large bore slugs sized 0.0005" under groove diameter shoot faster, with no loss in precision.  That approach seems perhaps better because it reduces friction all the way down the barrel, than slamming the slug into the rifling with a lot of free-bore. 

Of course, it depends how close the slug diameter is to the free-bore diameter.  If the free-bore is a gentle cone then it will align the slug with the barrel axis before the slug slams into the rifling.  What is the optimal free-bore for velocity, without degrading accuracy is the million dollar question.  Somehow, better precision seems more valuable than a few more FPE.  A trade-off one can't effectively speculate about, without absolute numbers.
« Last Edit: November 21, 2021, 04:34:39 PM by subscriber »
  • USA

Offline Greg_E

  • Sharp Shooter
  • ****
  • Posts: 941
  • yes
  • Real Name: Greg
Re: How much jump before pellet hits the grooves?
« Reply #101 on: November 21, 2021, 08:53:50 PM »
In theory, pellets can be shot accurately out of smooth bore.
  • USA, NY, Syracuse

Offline subscriber

  • GTA Senior Contributor
  • ******
  • Posts: 4709
  • yes
Re: How much jump before pellet hits the grooves?
« Reply #102 on: November 21, 2021, 09:02:08 PM »
In theory, pellets can be shot accurately out of smooth bore.

As long as the pellet head is adequately supported by the tube ID.

How do you know if a chamber is cut "too loose"?  The loaded pellet or slug falls out if you invert the open breech...  If the projectile fit is snug enough not to fall out, it should be pre-aligned adequately to shoot straight.
  • USA

Offline rsterne

  • Member 2000+fps Club
  • Bob and Lloyd
  • GTA Senior Contributor
  • *****
  • Posts: 25349
  • GTA Forums Person of the Year 2017
  • Real Name: Bob
Re: How much jump before pellet hits the grooves?
« Reply #103 on: November 21, 2021, 09:04:01 PM »
Quote
In theory, pellets can be shot accurately out of smooth bore.

if the pellet is PERFECT (concenricity, balance).... Any imperfections will require at least a slow twist rate for accuracy....

Bob
  • Coalmont, BC, Canada
Dominion Marksman Silver Shield - 5890 x 6000 in 1976, and downhill ever since!
Airsenal:
1750 CO2 Carbine, .177 Uber-Pumper, .22 Uber-Carbine, .25 Discovery, 2260 PCP 8-shot Carbine, 2260 HPA (37 FPE), 2560 HPA (52 FPE), XS-60c HPA in .30 cal (90 FPE), .22 cal QB79 HPA, Disco Doubles in .22, .25 & .30 cal, "Hayabusa" Custom PCP Project (Mk.I is .22 & .25 cal regulated; Mk.II is .224, .257, 7mm, .308 & .357; Mk.III is .410 shotgun and .458 cal), .257 "Monocoque" Benchrest PCP, .172/6mm Regulated PCP and .224/.257 Unregulated, Three regulated BRods in .25 cal (70 FPE), .30 cal (100 FPE) & .35 cal (145 FPE), .257 Condor (180 FPE).

Offline lennyk

  • Marksman
  • ***
  • Posts: 351
  • yes
  • Real Name: Lennard
Re: How much jump before pellet hits the grooves?
« Reply #104 on: November 23, 2021, 09:17:23 PM »
in my country we are only allowed smoothbore air guns in 177.

at 25m i would say they are very close

beyond 40m the key difference is stability in wind.
  • Port of Spain, Trinidad

Online oldpro

  • GTA
  • Administrator
  • GTA Senior Contributor
  • *****
  • Posts: 10363
  • yes
  • Real Name: Travis
Re: How much jump before pellet hits the grooves?
« Reply #105 on: November 30, 2021, 06:15:45 PM »
 having tested this exact thing in the past(two years ago) I found pellets shot from a smooth bore had far less accuracy then ones shot with even the slightest twist. Modern pcp guns are getting slower and slower on twist rates as compared to years past though as we are finding you do need twist but not nearly as much as once thought. The fx smooth twist is a great example of a smooth bore with just a slight twist at the very end. Very accurate with pellets and horrible with any solids. 
  • Katy, Texas
Raptor mini 2 in .25
Huben k1 .22
Diana 56
FX tarantula
Walther R8
LCS SK-19

Offline lennyk

  • Marksman
  • ***
  • Posts: 351
  • yes
  • Real Name: Lennard
Re: How much jump before pellet hits the grooves?
« Reply #106 on: November 30, 2021, 09:01:31 PM »
What smoothbore barrel did you use and what caliber?

having tested this exact thing in the past(two years ago) I found pellets shot from a smooth bore had far less accuracy then ones shot with even the slightest twist. Modern pcp guns are getting slower and slower on twist rates as compared to years past though as we are finding you do need twist but not nearly as much as once thought. The fx smooth twist is a great example of a smooth bore with just a slight twist at the very end. Very accurate with pellets and horrible with any solids.
  • Port of Spain, Trinidad

Offline Roboslug

  • Shooter
  • *
  • Posts: 91
  • yes
  • Real Name: Floyd
Re: How much jump before pellet hits the grooves?
« Reply #107 on: December 11, 2021, 10:46:41 PM »
In a past life before I had to use prescription glasses I would shoot shotgun slugs as a hobby.  My shotgun is a bone-stock Browning B-2000 auto with a smoothbore slug barrel.  Other than a .22 I don't have any rifles and never considered myself a rifleman, I was always just enamored with the idea of shooting slugs.  When I found a site that hosted postal matches I had to find a barrel.  I chased this for a couple of years trying countless slugs in the name of accuracy.  It was 18 months of shooting/searching (a slug) that grouped adequately before I adjusted the sights.  Though I never won, I did have fun. 

So yes, pellet/bore fit does matter.

50 yds
open sights
5 shots
12 ga smoothbore



  • USA, LA, Baton Rouge

Offline Greg_E

  • Sharp Shooter
  • ****
  • Posts: 941
  • yes
  • Real Name: Greg
Re: How much jump before pellet hits the grooves?
« Reply #108 on: December 27, 2021, 05:19:40 PM »
I'm having a hard time finding motivation to work on this. I keep seeing videos on the new AEA Big 9 and wondering if I should just stop messing with this thing. It's going to take a large pile of work, and a bunch more money to get close to what you can get out of the box with many of these AEA products.  :-[

The spiral flute reamer is spiraled the wrong way, so it is worse. Still trying to make something to help me with the straight flute reamer. I have an idea to try, and after this I might quit.
  • USA, NY, Syracuse

Offline subscriber

  • GTA Senior Contributor
  • ******
  • Posts: 4709
  • yes
Re: How much jump before pellet hits the grooves?
« Reply #109 on: December 27, 2021, 10:17:35 PM »
Finding motivation to get motivated can be difficult :)
  • USA

Offline Spin

  • Plinker
  • **
  • Posts: 179
  • yes
  • Real Name: Jerryy
Re: How much jump before pellet hits the grooves?
« Reply #110 on: December 30, 2021, 11:59:08 PM »
having tested this exact thing in the past(two years ago) I found pellets shot from a smooth bore had far less accuracy then ones shot with even the slightest twist. Modern pcp guns are getting slower and slower on twist rates as compared to years past though as we are finding you do need twist but not nearly as much as once thought. The fx smooth twist is a great example of a smooth bore with just a slight twist at the very end. Very accurate with pellets and horrible with any solids.
     "  The fx smooth twist is a great example of a smooth bore with just a slight twist at the very end. Very accurate with pellets and horrible with any solids. "
        I'm Shooting NSA, FX, and ASA slugs out of a .25 cal. 600mm STX barrel and and I wouldn't call the results, horrible. I have no experience with any of the designated FX slug barrels but if extreme bench shooters are tagging bullseyes and silhouettes at 300 yrd.'s and out, I'm guessing they are doing OK with them. ;D
  • USA, WI. Chilton

Offline nervoustrigger

  • GTA Senior Contributor
  • ******
  • Posts: 8041
  • The Grin Reaper
    • My youtube channel
  • Real Name: Jason
Re: How much jump before pellet hits the grooves?
« Reply #111 on: December 31, 2021, 12:26:08 AM »
Quote
I'm Shooting NSA, FX, and ASA slugs out of a .25 cal. 600mm STX barrel and and I wouldn't call the results horrible.

FYI, Travis was describing the original Smooth Twist in which only a portion near the muzzle is rifled.

The Smooth Twist X (STX) is a different design in which the entire bore is rifled.

While their twist rates on paper may be comparable, the former produced an actual rate much, much slower on account of the pellet already having reached near max velocity before hitting the rifling.  It would therefore skid through the rifling and pick up only a small fraction of the twist rate...sufficient to stabilize a pellet but far too slight to stabilize slugs.
  • MS
Conduct yourself so that when a man accuses you of something dishonorable, no one will believe him.
Barrel accurizing guide
My youtube channel
QB79 HPA conversion
2240 HPA conversion
Intro to PCP airguns

Offline Spin

  • Plinker
  • **
  • Posts: 179
  • yes
  • Real Name: Jerryy
Re: How much jump before pellet hits the grooves?
« Reply #112 on: December 31, 2021, 05:20:52 PM »
Quote
I'm Shooting NSA, FX, and ASA slugs out of a .25 cal. 600mm STX barrel and and I wouldn't call the results horrible.

FYI, Travis was describing the original Smooth Twist in which only a portion near the muzzle is rifled.

The Smooth Twist X (STX) is a different design in which the entire bore is rifled.

While their twist rates on paper may be comparable, the former produced an actual rate much, much slower on account of the pellet already having reached near max velocity before hitting the rifling.  It would therefore skid through the rifling and pick up only a small fraction of the twist rate...sufficient to stabilize a pellet but far too slight to stabilize slugs.
  Got It! Thanks Jason.
  • USA, WI. Chilton