Do any of you guys know what other Hatsan shares platforms with the Gladius? I just traded for one in.25 cal. and was looking for a shroud adapter that adapts to 1/2" NF to install a brake. Also haven'tfigured out what air tube it takes. I'd like to get an extra and run a regulator in it.Pete
Instead of making a new thread i resurrect this one.I have a Gladius in the mail that should arrive early next week, while i was waiting i went to the basement and found my rifle cleaning kit, bipods, sandbags etcetera.In there was the .177 BoreSnake, will that bras end fit thru the breach, or do i need to cut it off a tad?
Quote from: rambi83 on April 20, 2017, 04:16:41 PMInstead of making a new thread i resurrect this one.I have a Gladius in the mail that should arrive early next week, while i was waiting i went to the basement and found my rifle cleaning kit, bipods, sandbags etcetera.In there was the .177 BoreSnake, will that bras end fit thru the breach, or do i need to cut it off a tad?I haven't tried it on a .177 but nothing i had would work from the breach side. For initial and heavy duty cleaning, i just take the barrel off.
Quote from: d.lead.slinger on April 20, 2017, 06:01:39 PMQuote from: rambi83 on April 20, 2017, 04:16:41 PMInstead of making a new thread i resurrect this one.I have a Gladius in the mail that should arrive early next week, while i was waiting i went to the basement and found my rifle cleaning kit, bipods, sandbags etcetera.In there was the .177 BoreSnake, will that bras end fit thru the breach, or do i need to cut it off a tad?I haven't tried it on a .177 but nothing i had would work from the breach side. For initial and heavy duty cleaning, i just take the barrel off.I have not seen how the barrel is seated on this gun but i presume that you have to zero the rifle again or is it very precisely mounted so it won't be necessary?
JUst recently got a gladius long in .25, but canīt get her any faster than about 787 fps, after moore than 300 pellets trough the crony, i gave up with the hammerspring adjustment, but seeing you get the gladius over 850-900 i think something is wrong, and then it strucked me, maybe the powerwheel isnīt right where it should be, maybe someone on the factory had a bad day or something, cause my speed seems to be like on Power setting 4-5, but i must ask you how to get it out, is it just to screw it loose from the other side and pull it out, or do i need to take the hole gun apart? Are there any springs or ballbearings or poisinus squirrels that going to fly out all over the Place?
Quote from: AG72 on September 05, 2017, 09:36:51 AMJUst recently got a gladius long in .25, but canīt get her any faster than about 787 fps, after moore than 300 pellets trough the crony, i gave up with the hammerspring adjustment, but seeing you get the gladius over 850-900 i think something is wrong, and then it strucked me, maybe the powerwheel isnīt right where it should be, maybe someone on the factory had a bad day or something, cause my speed seems to be like on Power setting 4-5, but i must ask you how to get it out, is it just to screw it loose from the other side and pull it out, or do i need to take the hole gun apart? Are there any springs or ballbearings or poisinus squirrels that going to fly out all over the Place?If I remember correctly, there are no ball berrings. Removed the hex screw on the left side of the rifle, just watch out for the spring. The adjuster slides out from the right side of the gun. I believe there are two orings that will come out with the adjuster.Edit: on the low power note, it seems silly but make sure your air tube is screwed in fully.
Hello,I am really interested in that rifle, Longe version with a .25 caliber, but I would like it to be regulated.I have seen that a Huma Air regulator is available, but I don't even know what performance the rifle will have with the regulator installed.Do you have an idea of how many fpe are reached with regulator set to 110, 120... to 170 bar?