GTA
All Springer/NP/PCP Air Gun Discussion General => Machine Shop Talk & AG Parts Machining => Show Off Your Air Guns With Mods (SHOW and TELL) => Topic started by: sixshootertexan on January 08, 2018, 08:42:39 PM
-
I wanted a rifle that I could give the guys in the shooting match section a run for their money. I looked at a lot of different makers and tried to make a rifle with some of the best features and each one.
Here are the specs.
Lothar Walther barrel in .177 19" long
Timney trigger for a 1903 Springfield set at 1 pound
Boyds Featherweight Thumbhole stock in Sky Blue limited run Ripple Laminate
Ninja Pro V2 SHP Regulator set at 1300psi
UTG Leapers Accushot 3-12x44 Compact scope
Air tube, breech and lower is 7075 aluminium
Air tube has a working pressure of 4600 psi (I'll never fill that high)
Air Arms 8.4 pellets @ 820FPS
60 shots on a 3000psi fill.
Weight 10 pounds with scope
Lower with trigger and reg
(https://s26.postimg.org/9jxa6x721/20170402_115837.jpg) (https://postimg.org/image/84vpi75yt/)
(https://s26.postimg.org/ayyuvmspl/20170402_115825.jpg) (https://postimg.org/image/xawnp0rth/)
First testing of rifle
(https://s26.postimg.org/7ct1jb709/20170704_130213.jpg) (https://postimg.org/image/3t73ti4ad/)
19 shots at 30yds without a stock
(https://s26.postimg.org/jr8b143yx/20170910_115029.jpg) (https://postimg.org/image/k3zp7am8l/)
https://www.youtube.com/watch?v=4yFDOAXt0XY (https://www.youtube.com/watch?v=4yFDOAXt0XY)
-
Inletting the stock
(https://s26.postimg.org/58fv7ocux/20170910_072945.jpg) (https://postimg.org/image/xy2r4bgut/)
Scope mounted
(https://s26.postimg.org/4hn51wahl/20170910_102140.jpg) (https://postimg.org/image/93j9a8w0l/)
(https://s26.postimg.org/4l29a6dy1/20170910_102213.jpg) (https://postimg.org/image/lll5iuqz9/)
While I was having the aluminum anodized I install a carbon fiber tube 16mmx20mm
(https://s26.postimg.org/67ua91w9l/20171128_092852.jpg) (https://postimg.org/image/l3stgn7o5/)
(https://s26.postimg.org/69482gy3d/20171128_093556.jpg) (https://postimg.org/image/upmdwxytx/)
After I got the air tube back I sent it and the shroud to the hydrodipper and had them covered in a carbon fiber.
(https://s26.postimg.org/qe2hcl39l/20180108_160252.jpg) (https://postimg.org/image/asl5smrb9/)
(https://s26.postimg.org/om9ihozc9/20180108_160257.jpg) (https://postimg.org/image/y6t54koo5/)
(https://s26.postimg.org/aftrmhbmh/20180108_160302.jpg) (https://postimg.org/image/8o0srks9h/)
(https://s26.postimg.org/vphdxg28p/20180108_160356.jpg) (https://postimg.org/image/f1pvuy7h1/)
Pictures did not turn out to good I'll take some more this weekend, along with a shot string and target.
-
all your work is absolutely amazing ! id love to see a diagram of the valve and timney trigger configuration.!@ I still recall the 25 caliber co2 build that looked like a 5000 dollar gun.. excellent work man !
-
I'm not really into rifles, but that could change my mind, wow!... awesome work.
Wyo
-
Fantastic 8)
-
Very impressive project ... Thank you for sharing !
-
Thanks guys.
Ricky
-
Ricky
Outstanding build, one beautiful and accurate AR, you have the knack......... 8)
I love the mag sized loading port, I think I could even get my fingers in there.
Tia,
Don
-
Now that is Stunning!!! Wow-Just-WOW! 8)
Knife
-
nicely done
-
Again thanks everyone.
I did some testing this morning with AA 8.4 and 10.3 pellets. I shot 20 rounds of each at different velocities and this is the best I have for now.
AA 8.4
817
806
808
807
811
811
812
809
812
814
806
807
814
808
809
809
801
805
808
810
Highest 817
Lowest 801
Average 809
Extreme spread 16
SD 3
The target, 30yards, 2 sight in shots at the bottom, 18 shots at the crow, the gray area is the size of a dime, 16 shot under a dime with 2 flyers.
(https://s26.postimg.org/6f4qy65mh/Blue1.jpg) (https://postimg.org/image/t3txxqn05/)
-
Ricky,
Bueatiful build.
I'm looking forward to your results in the shooting match gate.
Jim
-
Ok I recrowned the barrel. I didn't like the way it looked. I did something wrong it's not shooting as good as last time. The velocity changed on me. I only took the upper portion apart but the FPS went up for some reason. I know it likes 800-820 fps it was hitting as high as 849. Maybe it was the baffles removed. Could be just breaking in after the anodizing.
Anyways made a video and a spread sheet.
(https://s26.postimg.org/eqvzwvknd/Blue3.jpg) (https://postimg.org/image/4426rgchx/)
https://www.youtube.com/watch?v=uouHTl6tPvc (https://www.youtube.com/watch?v=uouHTl6tPvc)
-
I wish I had your skills!!! I would love to build something very similar, but with the lower being able to mount a breech made for a disco... I have a custom side lever breech, not a normal breech... *sigh* one of these days!
How did you add a Remington style safety to the Springfield's trigger?
NVM, I did a quick search. I didn't know you could order a Timney trigger for a Springfield w/a safety... ::)