B26 pivot bolts help needed
Select Gate
READ GTA FORUM RULES BEFORE POSTING
GTA Forum Help Desk
GTA Announcement Gate
Dealer Area
GRIP
AirgunWeb Airgun Videos
Airgun Repository of Knowledge
Vendors and Vendor Videos
AirGun Expo 2021
Airgun Expo 2022
Contests and Giveaways!!!
Welcome New Members
In Memoriam
GTA Contributing Members
Shot Show Videos
Hajimoto Productions
Airgun Detectives
Air Gun Gate
BB Guns and Such
"Bob and Lloyds Workshop"
American/U.S. Air Gun Gates
European/Asian Air Gun Gates
PCP/CO2/HPA Air Gun Gates "The Darkside"
Air Archery
Vintage Air Gun Gate
Air Guns And Related Accessories Review Gates
Hunting Gate
Machine Shop Talk & AG Parts Machining
3D printing and files
Buyer's, Seller's & Trader's Comments
Bargain Gate
Back Room
Target Shooting Discussion Gate
Target Match Rules
Shooting Match Gates
Field Target Gates
The Long Range Club
100 Yard Match
Discussions By States
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email
?
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Home
About
Help
Old GTA
Gallery
Search
Stats
Login
Register
Advertise Here
GTA
»
All Springer/NP/PCP Air Gun Discussion General
»
European/Asian Air Gun Gates
»
China/Asian AirGun Gate
(Moderators:
ezman604
,
GTA-Airgunner
) »
B26 pivot bolts help needed
« previous
next »
Print
Pages: [
1
]
Go Down
Share This!
Author
Topic: B26 pivot bolts help needed (Read 608 times))
Marco2021
Marco 2021
Plinker
Posts: 224
yes
Real Name: Mark
B26 pivot bolts help needed
«
on:
September 09, 2017, 07:07:51 PM »
Hi all, I picked up a very nice Bam B26 today and understand it is a copy of Weirauchs hw 95. I tested it with half a dozen or so different pellets but yet another .177 that loves Crosman 10.5 premiers. After firing 12 or so shots the pivot bolts comes loose resulting in side side play and loss of accuracy. I re- tighten the bolt then it comes loose again. I guess there are washers inside the jaws that need replacing? All help appreciated.
Cheers
Mark.
Logged
New Zealand
AA TX 200 22 FAC. Hawke HD 3-9*40.
BSA LIGHTENING XL SE .grt .25
HATSAN 130S .30 x2
Benjamin Regal .177
Benjamin Prowler .177
Benjamin Varmint .22
Roadworthy
Honorary GTA Moderator
GTA Senior Contributor
Posts: 9706
yes
Real Name: Thomas
Re: B26 pivot bolts help needed
«
Reply #1 on:
September 09, 2017, 08:15:04 PM »
If it has not been apart the washers should still be there.
I would clean the threads on the screw and the associated nut then apply a thread locker following its instructions.
Loctite wants you to tighten the screw as desired then allow to set up for twenty four hours. If you tighten it later you break the bond and will need to clean and reapply.
Vibratite VC-3 wants you to let it set up for thirty minutes before reassembling the parts. You may tighten later if needed. VC-3 is more like a self locking nut than a thread locker.
Logged
Near the Southern Coast of Washington State
Real knowledge is knowing the extent of one's ignorance.
Kernbigo
Plinker
Posts: 162
yes
Real Name: oscar
Re: B26 pivot bolts help needed
«
Reply #2 on:
September 10, 2017, 10:50:24 AM »
only use the blue thread lock, the green or red you will never get it apart again
Logged
il.
Print
Pages: [
1
]
Go Up
« previous
next »
GTA
»
All Springer/NP/PCP Air Gun Discussion General
»
European/Asian Air Gun Gates
»
China/Asian AirGun Gate
(Moderators:
ezman604
,
GTA-Airgunner
) »
B26 pivot bolts help needed