• Jefferson State Airrifles
  • Air Gun Web - Expert Airgun Reviews
  • Hajimoto Productions
  • Airgun Angie - Backyard Shooting
  • Nielsen Specialty Ammo
  • Dynamic Air Rifles
  • FX Airguns
  • DonnyFL - When silence is a priority
  • Airgun Archery Fun
  • Pyramyd Air
  • Saber Tactical
  • New England Airgun
  • Umarex Airguns
  • Contact us
  • Utah Airguns
  • SEKHMET Airgun Accessories
  • Freedom Gun Targets
Jefferson State Airrifles
Air Gun Web - Expert Airgun Reviews
Hajimoto Productions
Airgun Angie - Backyard Shooting
Nielsen Specialty Ammo
Dynamic Air Rifles
FX Airguns
DonnyFL - When silence is a priority
Airgun Archery Fun
Pyramyd Air
Saber Tactical
New England Airgun
Umarex Airguns
Contact us
Utah Airguns
SEKHMET Airgun Accessories
Freedom Gun Targets


Recent Posts

Pages: [1] 2 3 ... 10
1
Boolit and Pellet Casting / Re: NOE News
« Last post by 35 shooter on Today at 11:02:11 PM »
Noe has a few 20 and 24 gr. molds in 22 cal. back in stock now.... just in case some have’nt noticed it yet that wanted one.
2
Back Room / Re: What are you listening to right now?
« Last post by lizzie on Today at 10:59:58 PM »
3
So, tried calling Extreem and got the good old automated shuffle again. After being on hold for near 10 minutes, auto-annie came on, said no one was available to answer my call and hung up.

Called the manufacturer, Aim Sports, back and got someone in CS. They said because I didn't purchase directly from them, for $393.29, that I would have to pay to ship the defective scope back to them and they would inspect it and send me a replacement. Guess I'll pay the $12 and deal with them as they said they would expedite the replacement.

Beats having to deal with that a-hole Matt at Extreem... ::)

I hope Aim Sports ships a new scope to you quickly.  Did they say if it will be used/refurbished or NIB?
4
Mine slugged out at .2154 I find This style sized down works best in these barrels,  https://noebulletmolds.com/site/product-category/224/218-25-rf-d6/

 Also AVS has a similar one that was designed for this bore and shoots lights out as is. https://avsslugs.com/product/22-caliber-slug/

Great info, Seneca are way oversized and I have a sizer coming, but it may be to big --- I have smaller sizers coming.

217 slugs are pretty darn tight :-(

wll

5
Big Bore AirGun Gate / Re: AEA Challenger .357 problem
« Last post by Dan H on Today at 10:51:18 PM »
here is a pic of the mag after I repaired it ....  it's been working perfect , Bin did send me a second new mag for my gun also  after I told him what happened ...

I's it possible something is forcing the bolts open?
  I don't really think so.....  I have tested by holding the bolt while firing , and no there is not enough movement to open / raise the bolt high enough to do that on my guns ...

I think it might also be easy to hit it with a finger and pop it back up in to a bad position , that bolt slides very easy ... like when you keep looking threw scope in between shot's ,and may not see the bolt accidently lifting is one thought I had ,and I thing might of happened to me in testing , so it's something to keep and eye on for sure ...

 1 thing at least   we did not get hurt ...  ::)
6
Back Room / Re: So....Whatcha Eating?
« Last post by bantam5s on Today at 10:49:06 PM »
Some blue bunny cookies n cream ice cream.
7
Air Gun Gate / Re: What airgun related did you do today?
« Last post by bantam5s on Today at 10:47:33 PM »
Resealed the Benjamin 132, and made a holster for it.



It took a minute to seal properly,  but now that it has woken up it's holding and shooting great.

Nice work, David!
Thank you.

It's not my best work,  but it's functional.
8
German AirGun Gate / Re: More HW50S love and now in 20 cal.
« Last post by tjk on Today at 10:47:12 PM »
Very nice looking setup Joanie!  And in .20 too. I know as you continue to shoot it, as it breaks in, you will really understand the 5mm caliber and appreciate its attributes as you do .177, .22, etc.  That stock design looks to be very user friendly. Cant wait to see future groupings as things progress.
9
Machine Shop Talk & AG Parts Machining / Re: New Lathe...
« Last post by Rob M on Today at 10:46:57 PM »
Ok, so it appears the headstock is mt3. The collets are 6k which are rare as hens teeth. There should be a pin in the spindle threads that is 1/8” in diameter to key the collets, but is usually snapped off on older machines. So no collet chuck needed and I seem to have all I need to use them. The pin that keys the collets will clear a normal mt3 center, but has a tendency to cause issues when trying to use the adapter to go down to a mt2 center.

pretty cool , never heard of them till now..
Pages: [1] 2 3 ... 10