Donation

Support Equipment For PCP/HPA/CO2 and springers ,rams > 3D printing and files

Would like to work with someone

<< < (3/4) > >>

sb327:
Is it something like this you are trying to make?

https://sureshot-airguns.co.uk/product/20-moa-riser-rail/

Dave

YEMX:

--- Quote from: sb327 on February 15, 2021, 01:03:12 PM ---Is it something like this you are trying to make?

https://sureshot-airguns.co.uk/product/20-moa-riser-rail/

Dave

--- End quote ---

What I have in my head is a complete replacement scope rail for the Impact that has a 20 moa cant and M-lok slots on the sides.  Not a add-on rail.

subscriber:
Tom,

Perhaps you could talk Sabre Tactical into adding that to their line of FX Impact products.  Can't hurt to ask: https://sabertacticalinc.com/pages/contact-us

Have you contacted FX  or resellers reps to see if such an animal exists already?
serviceusa@fxairguns.com
https://utahairguns.com/contactus/


Based on the Impact user manual and parts diagram (links below), the question is if you want to keep the integral side rails in the design; or keep thing simple/cheap and dispense with them? 

Parts diagram and list:  https://fxairguns.com/wp-content/uploads/2020/07/Impact-MkII.pdf
User manual:  https://fxairguns.com/wp-content/uploads/2020/06/Fx_Impact_2020.pdf







If you wanted super low Pic-Rail, then some of this rail stock below could be modified by milling a 20 MOA slope into it.  Then drilling the mounting screw hole pattern perpendicular with the new bottom that mates with the rifle:

https://alcobrametals.com/product/pre-slotted-picatinny-rail-extrusion/

YEMX:

--- Quote from: subscriber on February 17, 2021, 06:45:20 AM ---Tom,

Perhaps you could talk Sabre Tactical into adding that to their line of FX Impact products.

Have you contacted FX  or resellers reps to see if such an animal exists already?

Based on the Impact user manual and parts diagram (links below), the question is if you want to keep the integral side rails in the design; or keep thing simple/cheap and dispense with them? 

If you wanted super low Pic-Rail, then some of this rail stock below could be modified by milling a 20 MOA slope into it.  Then drilling the mounting screw hole pattern perpendicular with the new bottom that mates with the rifle:

--- End quote ---

I did forget to get in touch with Saber Tactical  ;)

One of the reasons I dropped the idea for now, is to see if FX would put a 20 MOA rail on the Impact/make a 20 MOA rail available as an accessory.  There's one on the Maverick as standard, so it stands to reason the Impact- their flagship model- would get a 20 MOA rail as well.  We'll see.  In case you were wondering, the Maverick rail isn't interchangeable w/the Impact.  At least, that's what I keep reading. 

My idea replaces the side picatinny rails with M-lok slots so the end user can decide whether or not to run pic rails

The problem with going too low, is that the scope will end up lower than factory, and would require high rings, which negates installing a low rail.  I changed my idea to keep the back of the rail factory height, and drop the front down to make the 20 MOA cant.  But with such a small angle change (and looking at prices to have the piece made), I felt that right now, this isn't something that I can develop affordably. 

subscriber:

--- Quote ---it stands to reason the Impact- their flagship model- would get a 20 MOA rail as well.
--- End quote ---

I am surprised that they don't have one standard already.

Navigation

[0] Message Index

[#] Next page

[*] Previous page