PyramydAir The Airgun Experts Umarex USA Airguns Utah Airguns Nielson Specialty Ammo Nielson Specialty Ammo FX Airguns DonnyFL Airgun Archery Fun Saber Tactical New England Airguns Evanix Airguns at Airgun Pro Shop Sekhmet USA Freedom Targets AirgunWeb Old School Airgun Reviews Hajimoto Productions Airgun Angie - Backyard Shooting Air Tanks Plus Jefferson State Air Rifles PyramydAir The Airgun Experts Umarex USA Airguns Utah Airguns Nielson Specialty Ammo Nielson Specialty Ammo FX Airguns DonnyFL Airgun Archery Fun Saber Tactical New England Airguns Evanix Airguns at Airgun Pro Shop Sekhmet USA Freedom Targets AirgunWeb Old School Airgun Reviews Hajimoto Productions Airgun Angie - Backyard Shooting Air Tanks Plus Jefferson State Air Rifles PyramydAir The Airgun Experts Umarex USA Airguns Utah Airguns Nielson Specialty Ammo Nielson Specialty Ammo FX Airguns DonnyFL Airgun Archery Fun Saber Tactical New England Airguns Evanix Airguns at Airgun Pro Shop Sekhmet USA Freedom Targets AirgunWeb Old School Airgun Reviews Hajimoto Productions Airgun Angie - Backyard Shooting Air Tanks Plus Jefferson State Air Rifles PyramydAir The Airgun Experts Umarex USA Airguns Utah Airguns Nielson Specialty Ammo Nielson Specialty Ammo FX Airguns DonnyFL Airgun Archery Fun Saber Tactical New England Airguns Evanix Airguns at Airgun Pro Shop Sekhmet USA Freedom Targets AirgunWeb Old School Airgun Reviews Hajimoto Productions Airgun Angie - Backyard Shooting Air Tanks Plus Jefferson State Air Rifles


Author Topic: Thinnest Kerf Saw  (Read 237 times))

Offline Ronno6

  • GTA Senior Contributor
  • ******
  • Posts: 2236
  • yes
  • Real Name: Ron
Thinnest Kerf Saw
« on: April 17, 2021, 12:34:13 PM »
I have need to cross-cut blanks to 10", or as close to that as possible, maybe 9 15/16" at shortest.
The lumber as purchased is 30" in length.
I would sure like to get 3 blanks out if each stick.
The lumber is 1-3/4" square.
I believe most of my radial saw or miter saw blades take about 1/8"
That'll cut things way too close, shaving that 1/16" off each of the first 2, but leaving me 1/16" shy on blank #3.
What type of saw is best for that thickness but take the least amount of kerf??
Japanese razor saw? Can they cut 1-3/4" stock?
I'm not sure I can cut too squarely on the bandsaw..

One end of the project parts has a slight angle which may make it possible to cross cut at a slight angle to make 2 blanks facing each other.
But, I would prefer to cut square.......
  • United States of America,Stone County, Mississippi
You can lead a man to water, but you can't keep him from urinating in it.

Offline Roadworthy

  • Honorary GTA Moderator
  • GTA Senior Contributor
  • ******
  • Posts: 9080
  • yes
  • Real Name: Thomas
Re: Thinnest Kerf Saw
« Reply #1 on: April 17, 2021, 01:31:57 PM »
To achieve a REALLY thin kerf requires a REALLY thin blade.  That gets iffy in thick materials and requires a great deal of patience.  A scroll saw would serve you well but the thickness of your wood would certainly create a difficult situation.  Perhaps a hack saw with a metal cutting blade, but you'd still be trying to hold it square.
  • Near the Southern Coast of Washington State
Real knowledge is knowing the extent of one's ignorance.

Online sb327

  • Sharp Shooter
  • ****
  • Posts: 834
  • yes
  • Real Name: David
Re: Thinnest Kerf Saw
« Reply #2 on: April 17, 2021, 02:03:28 PM »
A jap cut will be the best, IMO. It is still flimsy enough to need a guide for thick deep cuts. Maybe a miter box.

Other thinner blades are more for non square/straight cuts.

Dave
  • USA, OK, Stigler
Dave

Offline Firewalker

  • GTA Senior Contributor
  • ******
  • Posts: 2218
  • USN from birth to the grave
  • Real Name: David
Re: Thinnest Kerf Saw
« Reply #3 on: April 17, 2021, 02:09:40 PM »
My bandsaw wood blade has a 1/32" kerf. A Jap pull saw is probably close.
  • USA, MN, Mille Lacs
You may not go around, you must go through.

Offline Ronno6

  • GTA Senior Contributor
  • ******
  • Posts: 2236
  • yes
  • Real Name: Ron
Re: Thinnest Kerf Saw
« Reply #4 on: April 17, 2021, 03:49:01 PM »
Thanks, y'all.

I thought about using a coping saw to make a serpent cut,but
I found that my chop saw cuts an .083" or so kerf.
I laid out 2 parts nested nose to nose on a 19-7/8" length and, with an 11 degree angle cuts 'bout perfect!

I guess that's how I'll do it.
Now, I'll have to pay closer attention to grain orientation and which side goes up........
  • United States of America,Stone County, Mississippi
You can lead a man to water, but you can't keep him from urinating in it.