GTA
All Springer/NP/PCP Air Gun Discussion General => European/Asian Air Gun Gates => UK Airgun Gate => Topic started by: Razor62 on December 20, 2022, 03:12:32 PM
-
Just picked a beautiful TX200 in .22 cal. I've tried 4 different brands of pellets so far but nothing's shooting as well as the gun should shoot. Can't seem to do much better than 1" at 25 yards.
-
Clean the barrel well, treating it as a new gun. I like to use Hoppe's Number Nine or Ballistol for this purpose. This will eliminate most old fouling and build up. Do a tissue test to check the breech seal. For a pellet I suggest a mid weight, something like JSB Exact Match would probably be a good starting point. You'll probably have to experiment for the best weight for your particular gun. If you've not shot an airgun much part of the problem may be your hold. You must hold the gun as close to exactly the same way for every shot. Remember, unlike a firearm there's a delay between the time you pull the trigger and the time the pellet exits the gun. The recoil starts the gun moving before the pellet leaves the barrel. Consistency is key here. The gun should be capable of much tighter results than you're getting. My TX 200 is in .177 and will do 5/8" c-c five shot groups at forty yards. Practice, a decent mount, and a decent scope are critical.
-
Mine loves H/N FTT and shoots Crosman Hollow points exactly the same.. just have a flyer every now and then with the Crosmans..
-
With roughly 4000 pellets through my TX200 .22 cal, I seem to shoot best with Air Arms Diablos 16gr or JSB Exact Diablos in 15.86gr. Of note: this is just with my rifle, your's may well be different, but at least this is a place to start. Orv.
-
Thank you Thomas. I haven't cleaned the barrel. Perhaps that's all that's required. I'm very familiar with the need for consistency when shooting ny springers. Cleaning the bore however may correct the issue. Thanks very much. I'll give it a shot.
-
Thanks Dean. I've got both of those pellets ( my FTTs have a 5.53mm head diameter) but neither will shoot well in this rifle. Perhaps Thomas is correct and the bore needs cleaning. Thank you for your suggestions.
-
Thanks Orvil, I'll give those both a try. I'm a bit nervous because a friend had a TX in .22 and he could never get it to shoot well. His .177 TX on the other hand is wonderfully accurate.
-
After you clean the barrel take a close look at the crown and do a qtip test to see if you have any snags. Have you shot it over a chrony yet?
A ten shot string may reveal something or maybe not.
-
and check the stock screws!!!!!!!!!!! ;D
-Y
-
As I implied above, each gun shoots a bit differently with different pellets. My more than two years experience with my .22 cal TX200 MKIII copies nearly all others: the TX200 is a very accurate rifle. Although, for a springer, the TX200 isn't particularly sensitive to hold, for best accuracy, always shoot using the same hold . . . called the artillery hold. It's important to use the same cheek meld and to loosely hold the butt to the shoulder. Sight in at 10 yards and then 25 yds and your accuracy will come. My chronograph told me that my TX200 was ailing, so I'm in the process of doing a Vortek Tune on it now. Now that is,just as soon as I'm through with some "honey do" projects. Geeesh. Orv.
-
Mine likes the H&N FTT 5.53 head. The 5.54 head is accurate also but is much harder to load.
-
After you clean the barrel take a close look at the crown and do a qtip test to see if you have any snags. Have you shot it over a chrony yet?
A ten shot string may reveal something or maybe not.
Gotta' figure out how to remove the shroud before I can see the crown. I did chrono the rifle it's averaging 15.5 ft lbs with an extreme spread of 10 fps. with a Vortek Kit installed
and check the stock screws!!!!!!!!!!! ;D
Screws are tight.
As I implied above, each gun shoots a bit differently with different pellets. My more than two years experience with my .22 cal TX200 MKIII copies nearly all others: the TX200 is a very accurate rifle. Although, for a springer, the TX200 isn't particularly sensitive to hold, for best accuracy, always shoot using the same hold . . . called the artillery hold. It's important to use the same cheek meld and to loosely hold the butt to the shoulder. Sight in at 10 yards and then 25 yds and your accuracy will come. My chronograph told me that my TX200 was ailing, so I'm in the process of doing a Vortek Tune on it now. Now that is,just as soon as I'm through with some "honey do" projects. Geeesh. Orv.
-Y
Using the artillery hold and shooting off of a bag, makes no difference. I've cleaned the barrel thoroughly and waiting on the weather to get some trigger time with it.
Mine likes the H&N FTT 5.53 head. The 5.54 head is accurate also but is much harder to load.
Thanks. That's one of the pellets that I've tried so far. I'll keep trying.
I just want to thank everyone who took the time to respond. Thank you and Merry Christmas.
-
I shoot indoors at 25 yds at colored notebook paper reinforcement rings. Center hole is .250. Will shoot in the hole if I do my part 90% of the time. Good 5 shot groups are inside the hole all 5 shots. The accuracy amazes me. Front rest and rear bag, shoot it just like a centerfire It likes a very soft front bag, not sand.
-
Just an update....I found a pellet the shoots great. It's the JSB 18.13 gr. They shoot wonderfully. Hitting dimes at 55 yards.
Thanks to the gang for all of the suggestions and for the helpful replies.