Daystate Regal Teardown
Select Gate
READ GTA FORUM RULES BEFORE POSTING
GTA Forum Help Desk
GTA Announcement Gate
Dealer Area
GRIP
AirgunWeb Airgun Videos
Airgun Repository of Knowledge
Vendors and Vendor Videos
AirGun Expo 2021
Airgun Expo 2022
Contests and Giveaways!!!
Welcome New Members
In Memoriam
GTA Contributing Members
Shot Show Videos
Hajimoto Productions
Airgun Detectives
Air Gun Gate
BB Guns and Such
"Bob and Lloyds Workshop"
American/U.S. Air Gun Gates
European/Asian Air Gun Gates
PCP/CO2/HPA Air Gun Gates "The Darkside"
Air Archery
Vintage Air Gun Gate
Air Guns And Related Accessories Review Gates
Hunting Gate
Machine Shop Talk & AG Parts Machining
3D printing and files
Buyer's, Seller's & Trader's Comments
Bargain Gate
Back Room
Target Shooting Discussion Gate
Target Match Rules
Shooting Match Gates
Field Target Gates
The Long Range Club
100 Yard Match
Discussions By States
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email
?
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Home
About
Help
Old GTA
Gallery
Search
Stats
Login
Register
Advertise Here
GTA
»
All Springer/NP/PCP Air Gun Discussion General
»
PCP/CO2/HPA Air Gun Gates "The Darkside"
»
Daystate Regal Teardown
« previous
next »
Print
Pages: [
1
]
Go Down
Share This!
Author
Topic: Daystate Regal Teardown (Read 1160 times))
Jking
Marksman
Posts: 342
yes
Real Name: Jimmy
Daystate Regal Teardown
«
on:
October 18, 2016, 10:27:23 AM »
Some have shown some interest in this so I thought I'd share what I've learned on taking apart the Daystate Regal. I've had mine completely down to the valve and replaced a seat to stop a small leak I had a couple of years ago.
Step one, remove the scope and action from the stock,
Step two, to remove the upper receiver and barrel/shroud in one piece, loosen the three set screws on the barrel band (1.5mm) and slide the band off of the air tube.
Now remove the six screws holding the upper receiver to the valve body. Four are hex screws the other two down in the recess of the breech where the pellet probe is visible are regular slotted screws. Here's a kicker though the two front hex screws nearest the muzzle are 2.5mm and the back two by the bolt handle are 3/32".
With the top half off you can re-lube the bolt and associated moving parts. There is also a transfer port there to keep tabs on.
Step 3 to remove the hammer spring and the hammer the safety assemble needs to come off by removing the two 1.5mm set screws on the side of the valve body/trigger assembly. There will be some spring on it so beware.
Step 4 to remove the hammer for inspection or polishing remove the cocking lug hex screw that is viewable on top of the hammer body. Sorry I don't have a photo of it. With the hex screw removed you might have to rotate the hammer and pull the trigger to let it slide out.
Step 5 to remove the air tube to gain access to the valve, poppet and seat the air has to be drained from the air tube by loosening the gauge slowly and allowing the air to escape. Once you've confirmed 100% that the pressure is zero you can unscrew the air tube from the valve body.
This is what you should be down to, just the valve body and trigger assembly still attached with the two sealing O-rings.
Step 6 to remove the valve seat and poppet, remove the valve by unscrewing the valve assembly from the valve body.
The little yellow donut which is the seat just sits in the bottom of the valve body. This is what was leaking on mine.
That's it in a nut shell, I ended up polishing the bottom of the valve body to get a good seal on the yellow seat.
«
Last Edit: December 09, 2017, 10:16:29 AM by Jking
»
Logged
NM, Hobbs
FX Wildcat 25cal Sightron 4-20 Stac
FX500 Regulated, Sightron SIII
FX Crown 25cal Sightron SIII
airborne
Shooter
Posts: 10
yes
Real Name: peter
Re: Daystate Regal Teardown
«
Reply #1 on:
October 18, 2016, 11:08:40 AM »
Thanks for taking the time Jim and share this with us
Logged
pa
CatbirdSHV
Plinker
Posts: 144
yes
Real Name: John Babb
Daystate Regal Teardown - Ahh, That Hit The Spot!
«
Reply #2 on:
October 18, 2016, 12:46:42 PM »
Great, clear pics, and instructions. Thanks so extra very deluxe much!
Logged
Shreveport LA
Eschew Obfuscation
PRod .22
FX Impact MkII PP Slugliner .22
FX Dreamline Classic .22
Beeman R9 .22
Print
Pages: [
1
]
Go Up
« previous
next »
GTA
»
All Springer/NP/PCP Air Gun Discussion General
»
PCP/CO2/HPA Air Gun Gates "The Darkside"
»
Daystate Regal Teardown